Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Staten Island
Gate repair in Staten Island usually means one of two things: a sagging ornamental iron gate that won’t latch, or an automatic opener that stopped responding. We fix both, and most jobs are done in a single visit. Our Gate Repair team works across the whole borough, from Tottenville up to St. George, and we answer the phone live around the clock. Call (626) 649-4572 and you’ll get a written price before any work starts.
Staten Island has more ornamental driveway gates per block than any other NYC borough. That changes the work. We’re not just swapping hinges on a utility gate; we’re matching scrollwork, resetting posts that have shifted in saturated ground, and re-hanging heavy panels on pillars that have been standing since before the Verrazano opened. If you live here, you already know salt air and coastal wind are harder on iron than a midtown address ever was. We plan for that.
Why Latch & Post Gate Repair Is Staten Island’s Preferred Gate Repair Company
This work has a rhythm on Staten Island that you only learn by doing it. The South Shore’s 1960s colonials have concrete pillar-flanked driveways built for ornamental gates from day one. The North Shore’s older brick and brownstone posts have settled over a century, throwing hinges out of plumb in ways that need patience, not force. We know the difference between a post that needs resetting and a panel that just needs a sag correction. That judgment is what keeps a gate working for years instead of months.
Cody Beckman, our owner, built this company inside the Cedarwell family in 2009 around one idea: a gate is only as good as the latch that holds it and the post that carries it. Every job we do follows the same routine: a written price before we touch anything, shoe covers and drop cloths inside your home, and a photo of the clean-up before we leave. If a repair isn’t right, the 365-Day Done Right Promise covers it. No argument, no fine print.
Staten Island customers call us because they’ve had crews show up late, leave gate grease on the driveway, or hand them an invoice that doesn’t match the quote. We don’t do any of that. The quote you approve is the price you pay, and we answer calls 24/7 with a live person, not a voicemail.
Commercial Gate Repair in Staten Island
Commercial Gate Repair on Staten Island covers a lot of ground: sliding gates at industrial lots along the Arthur Kill waterfront, swing gates at condo complexes in Annadale and Eltingville, and barrier arms at parking facilities near the Staten Island Ferry terminal in St. George. The coastal exposure is the common thread. Salt air off the Kill Van Kull eats through gate operator housings and limit switches faster than most property managers expect, and high wind load on solid-infill gates racks panels and snaps hinge welds during a bad nor’easter.
For most commercial gate work on Staten Island, a service call runs $150 to $250, with repairs typically landing between $300 and $1,800 depending on whether we’re replacing a hinge, rewiring an operator, or rebuilding a post base. You’ll see the exact number in writing before we start.
Sliding Gate Track and Roller Work
Commercial sliding gates in Great Kills and Charleston take a beating from road salt and gravel. We replace worn roller assemblies, clear debris-packed tracks, and re-align steel V-track so the gate doesn’t buck under load. If the gate has been running rough for months, chances are the rollers are ovaled and the track has shifted; we’ll tell you honestly what needs replacing and what still has life.
Operator and Access Control Repair
Most commercial gate failures on Staten Island come down to the operator, not the gate itself. We service Linear, Viking, Doorking, and LiftMaster operators, including loop detectors, safety photo eyes, and keypad entry systems. A dead operator on a cold morning after a freeze-thaw cycle is a common call in the industrial zones off Richmond Terrace, and we can usually get it running the same visit.
Iron Gate Repair in Staten Island
Iron Gate Repair on Staten Island is different from anywhere else in the city because so much of the borough’s ironwork is ornamental. This is curb-appeal craftsmanship. We restore powder-coat finishes, match scrollwork on damaged sections, and align heavy swing gates on masonry pillars that have been standing for 40, 60, or 100 years. In neighborhoods like Great Kills and Tottenville, a driveway gate isn’t just security; it’s part of the home’s face.
Most residential iron gate repairs in Staten Island run between $200 and $600 for hinge and latch work. A full sag correction with post resetting runs $450 to $900. Weld repair on cracked scrollwork or snapped hinges starts around $150 per weld point.
Hinge and Post Reset Work
When an iron gate drags on the driveway or won’t latch, the hinge post is usually the culprit. Freeze-thaw cycles in saturated soil heave the post out of plumb, and the gate follows. We reset the post in new concrete, re-hang the panel, and confirm the latch catches cleanly before we leave.
Rust and Weld Repair
Salt air off the Upper New York Bay rusts iron gates from the inside out. We grind out rust pockets, weld in new steel where the section is too far gone, and re-coat the repair so it doesn’t fail again next season. The goal is a patch that looks like it was always there.
Trusted Brands We Service in Staten Island
Most Staten Island homes with automatic gates run one of a few brands: Linear, Viking, Ghost Controls, or DoorKing. Our technicians are factory-trained on all of them, including LiftMaster and FAAC, so the right fix happens on the first visit. We keep common parts in local stock, which means less waiting when a control board dies or a limit switch fails. And because every call is answered by a live person, you’ll know right away whether we can get your gate moving the same day.
Common Gate Repair Problems We See in Staten Island Homes
- Salt-air corrosion on hardware. The Upper New York Bay, Kill Van Kull, and Arthur Kill wrap around the island, and the salt air pits lag bolts, hinge pins, and motor housings years before an inland gate shows any wear.
- Freeze-thaw post heave. North Shore brick and brownstone posts have settled and shifted over decades. Every winter, water in the soil around the footing freezes and expands, pushing the post off plumb and making the gate drag.
- Wind damage to solid-infill panels. Coastal storms rack solid gates, snapping hinges and warping panels. This is especially common on East Shore homes that were rebuilt after Sandy, where surviving gates sit at odd grades or on compromised pillars.
- Sagging swing gates on aging pillars. Eltingville, Annadale, and Great Kills have thousands of 1960s-era concrete pillars that are slowly settling. The panel itself is often straight; the post is what’s moved.
Pricing for Gate Repair in Staten Island, NY
A standard latch replacement or hinge adjustment in Staten Island runs $180 to $340. A full sag correction with post resetting runs $450 to $900, depending on whether we’re digging a new footing or just re-plumbing an existing post. Automatic opener repairs run $225 to $600 for control boards, limit switches, and safety photocells. Full operator replacements run $800 to $2,200 installed, depending on brand and gate weight. Every quote is written, and every quote is agreed to before we start. Call (626) 649-4572 for a free estimate, and we’ll send a technician to measure, inspect, and give you the number you’ll actually pay.
We Also Serve Cities Near Staten Island
Beyond Staten Island, our Gate Repair in Staten Island service area reaches Brooklyn, Manhattan, the Bronx, and Long Beach. If you have a property outside the borough, call us and we’ll tell you when we can be there.
Serving Staten Island, NY - Our Local Coverage Area
We’re based in the Staten Island area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Staten Island
Nearly every automatic gate operator has a manual release mechanism: a key, a pull handle, or a crank that disengages the motor from the gate so you can push it open by hand. On Linear, Viking, Ghost Controls, and DoorKing units, the release is usually accessible without disassembling the operator housing. Check the side of the operator or consult the manual; the release is designed for exactly this situation. Once power returns, re-engage the motor and run a full open-close cycle to confirm the gate resets correctly. If you can’t locate the release or the gate won’t move manually, call us at (626) 649-4572 and we’ll walk you through it.
On Staten Island, a sagging gate usually means the hinge post has shifted, not that the hinges themselves are bad. Freeze-thaw cycles in saturated ground push the post footing out of plumb, and no amount of hinge tightening will fix that. The post has to be reset, or in severe cases, the gate panel needs a sag correction with a tension rod or structural reinforcement. If your gate has been adjusted twice and still drags, the post is the problem.
Yes. Safety photocells are what stop a closing gate when a child, a pet, or a car is in the path. They’re required under UL 325 safety standards for automatic gate operators, and we won’t put a gate back into automatic service without working photocells. If your gate is closing on objects or reversing unpredictably, the photocells are likely misaligned, blocked, or failed. Call (626) 649-4572 and we’ll test, clean, and re-aim them.
Staten Island is surrounded by salt water: the Upper New York Bay on the north, Kill Van Kull on the northeast, and Arthur Kill on the west. Salt air settles on iron and aluminum continuously, accelerating pitting and rust far faster than inland addresses. Combined with heavy road-salt use on hilly residential streets, your gate’s hardware, post anchors, and motor housings get a constant salt bath. That’s why we recommend stainless or sealed hardware replacements where possible, and why we grind out rust instead of painting over it.
Often yes. If the pillar itself is intact but the footing has shifted, we can excavate around the base, re-plumb the pillar, and pour a new footing without touching the driveway or the rest of the wall. If the pillar is cracked through or leaning more than a few degrees, a partial rebuild may be needed. We’ll tell you after a site inspection, in writing, before any work starts. Call (626) 649-4572 for a free on-site look.
Written by Cody Beckman, Owner at Latch & Post Gate Repair, serving Staten Island since 2009.