Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Electric Gate Repair Across Fresno
Electric gate repair in Fresno typically runs $150-$400 for common fixes like opener motor replacement, keypad repair, and safety sensor realignment, with full operator retrofits landing between $900 and $2,600. Most repairs we handle in Fresno are done the same day we arrive, because our trucks carry the control boards, hinge hardware, and safety sensors this market actually needs. If your gate won’t budge, won’t stop, or groans like it’s dragging through wet clay, call (626) 649-4572 and a live person answers, day or night.
Fresno’s soil shifts. That’s not a metaphor. The alluvial clay under neighborhoods like Sunnyside and the older southeast side swells in winter and bakes hard in summer, and gates hung ten or fifteen years ago were rarely footed deep enough for that kind of movement. We see the result every week: hinge posts leaned out of plumb, latches that won’t catch, slide gates that bind on their tracks by 3 p.m. on a 108-degree afternoon. This is the Electric Gate Repair work we do most often in Fresno, and it asks for a crew that knows the ground before they touch the gate.
Key Takeaways
- Common Fresno repairs cost $150-$400; full operator replacement runs $900-$2,600.
- Clay soil heave and Tule fog corrosion cause failures most generic gate companies misdiagnose.
- We service Linear, Viking, Ghost Controls, and DoorKing, with parts stocked for Fresno’s housing stock.
- Written price before work starts, shoe covers and drop cloths on every visit, cleanup photo before we leave.
- Live person answers 24/7 at (626) 649-4572.
Why Latch & Post Gate Repair Is Fresno’s Preferred Electric Gate Repair Company
We’re not a handyman with a gate side hustle. Latch & Post Gate Repair is part of the Cedarwell family of gate specialists, operating since 2009 with a single focus: gates that open, close, latch, and stop when they should. That focused workmanship matters in Fresno, where the combination of expansive clay, summer heat over 110°F, and winter fog creates failures most coastal technicians have never diagnosed. Our background-checked, uniformed techs are factory-trained on the brands Fresno families actually own, including Linear, Viking, Ghost Controls repair in Fresno, and DoorKing.
Every Fresno job follows the Cedarwell Care Promise without exception. We write the price before we open a panel. We put shoe covers on at the door and lay drop cloths on the floor inside, because your floors matter as much as your gate. We ask before we move or touch anything. And before we leave, you get a photo showing the work area cleaned up. Cody Beckman has led this team since the beginning, and his rule is simple: if the repair isn’t right 365 days after we leave, we come back and make it right. No argument, no fine print.
Gate Opener Repair in Fresno
Gate opener repair in Fresno usually lands between $160 and $380, depending on whether we’re replacing a capacitor, a limit switch, or the full motor gear assembly. A gate opener in this city works harder than the same unit would in a coastal town. Summer heat pushes the motor past its rated duty cycle, and the fine dust that drifts up from farm roads near the ag fringe works into the drive gears and rollers. When the opener hums but won’t move the gate, or trips its breaker a few times a week, the motor is often still fine. It’s the gear assembly or the capacitor that gave up, and that’s a repair, not a replacement.
Limit Switch and Control Board Work
Fresno’s older operators, especially first-generation Linear and DoorKing units, fail in predictable ways tied to our climate. A west-facing steel gate heats the control board inside the operator box; repeated 110-degree days crack solder joints and fried capacitors. We replace the board, re-set the limits, and the operator runs cleanly again. Cost is typically $220-$340 for a board swap on these brands.
Wiring and Sensor Repairs
UV from Fresno’s long summers degrades the insulation on low-voltage wiring run along gate posts and fences. The wires still pass current, but they short intermittently against the post or each other, which is why your gate works fine one hour and goes dead the next. This is often misdiagnosed as a motor failure. We trace the run, replace the damaged section, and seal the connections. Expect $120-$220.
Automatic Gate Repair in Fresno
Gate Installation - Fresno and automatic gate repair in Fresno addresses the entire system, not just the opener: the gate leaf, hinges, posts, track, operator, keypad, and safety sensors as one coordinating machine. Most automatic gate failures in Fresno start outside the operator. The hinge post shifts in the clay, the gate leaf sags, and the operator now fights gravity and friction it was never rated for. The opener burns itself out trying. So we always check the post and hinge alignment before condemning a motor. Typical automatic gate repair here runs $180-$400 for hinge resets, sensor alignments, and keypad reprogramming.
Thermal Binding and Track Work
West-facing slide gates on steel tracks expand in the afternoon heat. By mid-summer the clearance that was fine at 8 a.m. disappears by 3 p.m., and the gate stalls out exactly when the family is trying to get home. We re-set track clearances, replace worn rollers, and correct post alignment, a repair that usually runs $200-$350.
Keypad and Remote Programming
Keypads on Fresno gates corrode from Tule fog moisture even while the rest of the hardware looks dry. If your keypad buttons work inconsistently or the remote only opens the gate from six feet away, that’s usually antenna or keypad membrane damage from moisture. We repair or replace the keypad and reprogram your remotes. Cost is typically $95-$180.
Trusted Brands We Service in Fresno
Our Fresno trucks run stocked with the parts that fail on this soil and in this heat. We service Linear and DoorKing swing and slide operators, Viking barrier gates that guard HOA entrances in master-planned communities off Highway 99, and Ghost Controls systems on newer ranch-property installations. Our technicians are factory-trained on these brands, so the correct repair happens on the first visit, not the third. When a control board has been discontinued, we know which retrofit boards fit the existing mounting pattern, saving Fresno homeowners the cost of a new operator. For more on our approach, see our Electric Gate Repair service hub, and read about the neighborhoods we cover on our Fresno page.
Common Electric Gate Repair Problems We See in Fresno Homes
- Post heave and gate sag: Fresno’s alluvial clay swells in winter and shrinks in summer, pushing gate posts out of plumb. A gate that sagged two inches since spring usually has a shifted footing, not a bent hinge. We reset the post and re-align the gate leaf.
- Afternoon thermal binding: West-facing steel slide gates expand enough in 110-degree heat to bind on their tracks every afternoon. The repair is a track clearance adjustment and roller replacement, not a new operator.
- Legacy control board failure: Older LiftMaster and FAAC boards run fine for years, then fail suddenly after a heat wave or a fog season. Discontinued boards require a retrofit, and we carry the compatible current boards for the common Fresno builder-era models.
- Tule fog corrosion: From November through February the Valley floor sits under dense fog, and moisture condenses on hinge pins, keypad membranes, and circuit boards. Failures show up in March, puzzling customers who know Fresno as dry. We treat corrosion as a regular seasonal repair here.
Pricing for Electric Gate Repair in Fresno, TX
Here are the numbers we quote most often in Fresno. Keypad repair or replacement: $95-$180. Safety sensor realignment or replacement: $120-$200. Limit switch or control board replacement: $200-$340. Hinge reset and post re-alignment: $180-$320. Full operator replacement with labor: $900-$2,600, depending on brand and gate weight. You get the exact price in writing before any work starts. We don’t quote by phone and then revise on the driveway. The only time cost moves is if we open a panel and find additional damage, and even then we show you the issue and get your sign-off before touching it.
We Also Serve Cities Near Fresno
Latch & Post Gate Repair handles electric gate work across the surrounding communities we regularly dispatch to: Missouri City, Manvel, Stafford, and Sugar Land. If you’re just outside the Fresno boundary and your gate operator is down, call us. We’ll let you know straight whether we can route a truck to you that day, and the written price is always before the work, not after.
Serving Fresno, TX - Our Local Coverage Area
We’re based in the Fresno area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in Fresno
Your hinge post has almost certainly moved. Fresno’s clay soil heaves in winter and contracts in summer, and a 4-inch steel post can shift sideways over an inch in a single wet season. Adjusting hinges masks the symptom but won’t fix the footing. We probe the post depth, reset the footing when needed, and re-align the gate so it latches cleanly. Call (626) 649-4572 for a free estimate on the repair.
The midday sun expands the steel gate leaf and track, reducing the clearance until the gate binds and the operator stalls. West-facing gates in Fresno hit this every summer. The fix is a track clearance re-set and often new rollers, not a new operator. Most of these summer-binding repairs run $200-$350.
It depends on what failed. If the motor and gear assembly are tired but the control board is still supported, we can often repair for $200-$400. But if the board is fried and the parts are obsolete, retrofitting or replacing the operator is cheaper than chasing discontinued electronics. We’ll show you both numbers in writing before any work. Call (626) 649-4572 and a live person will set up the visit.
Current UL 325 standards require entrapment protection, which means monitored safety sensors or an equivalent device on any automated gate installed after the standard took effect. A Fresno gate hung in the 1990s may predate that requirement. When we service an older operator, we quote the sensor upgrade as part of the repair, so your gate runs safely and meets current expectations. The sensor addition typically adds $120-$200 to a repair.
Because Fresno gets Tule fog. From November through February, dense fog sits on the Valley floor and condenses directly onto metal surfaces. Hinge pins rust, keypad membranes swell, and circuit boards corrode, even with almost no rainfall. We use corrosion-resistant hardware on all Fresno hinge replacements and can swap keypads to sealed units for wet exposure. Call (626) 649-4572 for an exact price on the fix.
Call Latch & Post Gate Repair in Fresno
If your electric gate is down, sagging, or stalling in the afternoon heat, call (626) 649-4572. A live person answers, day or night. We’ll schedule a Fresno visit, give you a written price before any work starts, and leave your property cleaner than we found it, with a cleanup photo to prove it. Every repair is covered by the 365-Day Done Right Promise. If it isn’t right, we make it right, no fine print.
Written by Cody Beckman, Owner at Latch & Post Gate Repair, serving Fresno through the Cedarwell family of gate specialists.