Electric Gate Repair in Everman - On-Site in 60 Minutes, Fixed the Same Day

Fast, Reliable Electric Gate Repair Across Everman

Electric gate repair in Everman usually runs $180 to $640 depending on whether the fault is in the post, the operator, or the control board. Most calls we take from Everman homeowners are answered same-day or next-day, and a live person picks up the phone around the clock at (626) 649-4572. What we see most often in this city isn’t a dead motor. It’s a gate post that Tarrant County clay has heaved out of plumb, and a gate that then binds, drags, or trips its own safety sensors. That local pattern changes how we diagnose every single call here.

Call (626) 649-4572

Why Latch & Post Gate Repair Is Everman’s Preferred Electric Gate Repair Company

We work on gates built decades ago, and we know what the original installers in Everman did and didn’t do. Most posts in the older blocks were set in shallow concrete plugs, and every wet spring pushes them around. Our technicians are trained on Viking, Ghost Controls, and DoorKing equipment, so when a 1980s swing gate operator faults out, we check the post before we touch the motor. That order of operations saves Everman homeowners money and repeat visits.

Our crews arrive background-checked and in uniform, and the Cedarwell C.A.R.E. values are part of every job. We lay drop cloths where we walk, put on shoe covers before stepping inside, and take a cleanup photo before we leave. When kids are napping or a dog is behind the gate, we work quietly and ask before moving anything in the yard. The written price comes first, every time, and it doesn’t change once we start working.

We’re part of the Cedarwell family, independently owned and operated since 2009, and focused only on gates. Not fences, not general handyman work. That focus is why we stock parts for the brands Everman homes actually have, and why we can usually finish a control board replacement or gate motor repair in one visit.

Gate Access Control in Everman

Gate access control in Everman covers the keypads, remote receivers, intercoms, and vehicle loop detectors that tell your gate when to open and when to stay put. On older Everman properties, these systems were often added piecemeal years after the gate went in, so wiring runs along fence lines, connections sit in weather-exposed boxes, and the access control fails before the gate itself does. When a keypad stops accepting codes or a remote only works from ten feet away, the issue is usually corroded wiring or an outdated receiver, not the gate motor.

Keypads and Remote Receivers

A keypad that flickers or won’t take a code is often fighting moisture inside its housing or a failing ribbon connection. We bench-test the pad first, then check continuity to the operator. Most keypad replacements in Everman run $140 to $320, including programming and waterproof sealing.

Loop Detectors and Vehicle Sensors

Loop detectors buried in the driveway tell the gate a car is parked on it. In Everman’s clay, shifting soil can crack the loop wire and create false detection or none at all. We saw a loop on a home near the Everman High School football field that read phantom vehicles every afternoon until we dug it out and laid a new loop at proper depth.

Commercial Gate Operator in Everman

Commercial gate operator work in Everman means slide gates and swing gates on apartments, churches, small industrial lots, and the storefronts along Everman Parkway and east of I-35W. These operators cycle dozens of times a day, and when one fails, the gate stays open or stays shut, both of which cause problems. We service Viking, DoorKing, and Elite commercial operators, and we keep common boards and limit switches stocked so a Everman business isn’t waiting on parts for a week.

Slide Gate Operators and Rack Alignment

Slide gates fail when the rack and pinion misalign or a wheel carriage wears out. In Everman, clay movement also twists the track slightly, and the operator then draws more current and burns out its own board. We check rail alignment before replacing any motor, because replacing a board without fixing the track just kills the new board too.

Safety Edge and Photocell Retrofits

Older commercial operators in Everman sometimes lack modern entrapment protection. A safety edge or photocell retrofit brings the gate into compliance and keeps employees and delivery trucks safe. We quote the retrofit separately and explain what’s code-required before we order a single part. Expect commercial operator repair or retrofit work in Everman to run $480 to $1,400 depending on operator type, access control integration, and whether the post or track needs correction first.

Trusted Brands We Service in Everman

We’re factory-trained on the gate equipment Everman actually has, including Viking, Ghost Controls, DoorKing, and Elite. When your opener is a Ghost Controls unit on a backyard double gate or a Viking commercial slide operator at a Everman church, we know the wiring, the boards, and the failure points. We keep local parts stock so most residential repairs in Everman close out same-week, and if a board is obsolete, we’ll tell you honestly and price a retrofit rather than stringing you along.

Common Electric Gate Repair Problems We See in Everman Homes

• Heaved posts and dragging gates: Tarrant County’s expansive black clay swells after spring rains and shrinks in 100°F summers. Shallow footings from original 1960s and 1970s installs let posts move two or three inches, leaving a gate that scrapes the driveway or won’t latch. Correcting the footing depth is the only fix that lasts.
• Aging tubular steel and chain-link hardware: Homes built between the 1950s and 1980s often still carry original hinges, drop rods, and latch posts. These parts are decades past service life, and sag correction attempts fail at the hinge post even when the panel itself is straight.
• Obsolete control boards with no safety entrapment: Operators installed before modern UL 325 requirements often lack photocells or current-sensing obstruction detection. A gate that reverses for no reason, or won’t reverse when it should, frequently needs a board retrofit, not a motor swap.
• Freeze damage from hard freezes: The February 2021 event cracked welds and bent rails on frames already stressed by summer heat. A gate that worked fine in December can bind in February because a rail shifted and the rack no longer lines up with the operator arm.

Pricing for Electric Gate Repair in Everman, TX

We Also Serve Cities Near Everman

While this page focuses on Electric Gate Repair in Everman, our crews also handle gate work in Houston, San Antonio, Dallas, and Fort Worth. If you’re a few miles outside Everman proper, call us and we’ll confirm coverage and get you scheduled. The same written price, shoe covers, and cleanup photo apply.

FAQs About Electric Gate Repair in Everman