Electric Gate Repair in Converse - On-Site in 60 Minutes, Fixed the Same Day

Fast, Reliable Electric Gate Repair Across Converse

Electric gate repair in Converse, TX usually comes down to one of three things: a builder-grade operator that was never quite right, a hinge post that has heaved out of plumb on Blackland Prairie clay, or wiring that was never run properly when the house went in. Most calls we take from Converse homeowners are automation retrofits on 1998-2012 tract-home gates, where the operator is actually fine but the post underneath it is tilting, or there is no dedicated 120V power at the gate line at all. We fix all of it, and we give you a written price before any work starts. Call (626) 649-4572 and a live person answers, any hour.

Call (626) 649-4572

Why Latch & Post Gate Repair Is Converse’s Preferred Electric Gate Repair Company

We’re the Electric Gate Repair team at Latch & Post, part of the Cedarwell family of independently owned and operated gate specialists. Since 2009, we’ve focused on one trade: gates. Not fences, not general handyman work. Gates only. That narrow focus means our technicians have seen the exact failure pattern that runs through Converse subdivisions off Judson Road and FM 1516: manual cedar swing gates hung in the early 2000s, then retrofitted years later with an operator bolted on, but no power run and no conduit to protect what little wiring exists. When one gate on a Converse block starts dragging or faulting, we know the neighbors’ gates are usually weeks behind it, because the same builder used the same shallow footing.

Every Converse job gets the Cedarwell Care Promise as a non-negotiable part of the visit. Our technician writes the price down and you approve it before any tool comes out. We put shoe covers and drop cloths down before we step inside your home, and we take a photo of the clean-up before we leave. That’s not an upsell. It’s just how every visit goes. If the repair isn’t right, the 365-Day Done Right Promise means we come back and make it right, no argument, no fine print. Cody Beckman leads our technicians, and every one of them is background-checked, uniformed, and factory-trained on the brands Converse families actually have bolted to their gates: FAAC, BFT, Linear, and Viking, among others.

Commercial Gate Operator in Converse

Commercial Gate Operator work in Converse covers the sliding and swing operators on gated entries at churches, small offices, and multifamily properties along corridors like Toepperwein Road and Kitty Hawk Road. The job usually involves diagnosing an operator that won’t hold its limit settings, a control board that has stopped responding to the keypad, or a motor that hums but won’t move the gate. In Converse, commercial operators run roughly $450-$1,200 for board and motor repairs, and we stock or quickly source parts for FAAC, BFT, Linear, and Viking operators so you’re not waiting a week for a generic part to ship.

Slide Gate Operator Service

Most commercial slide gates in Converse sit on concrete that was poured without much slope correction, so the operator’s gear rack gets grit and clay fines packed into it after heavy spring rain. We clean the rack, reset the clutch, and adjust the limit cams. You’ll see the written price before we start.

Vehicular Swing Gate Operator Replacement

When a full replacement is the honest call rather than a board swap, we tell you that plainly. A new commercial swing operator for a Converse property typically runs $1,800-$3,200 depending on the gate’s weight and cycle count. We quote it in writing, you approve it first, and the 365-Day Done Right Promise covers the install.

Gate Opener Repair in Converse

Gate Opener Repair in Converse often starts with a homeowner telling us the gate groans, stops halfway, or trips the breaker on a wet morning. On 1998-2012 tract homes, the root cause is rarely the opener itself. It’s the hinge post heaving on expansive clay, or exposed landscape conduit that cracked and let water into the low-voltage line. Repair pricing for Gate Opener Repair in Converse typically runs $185-$420 for boards, limit switches, and photo-eye realignment. A full operator swap runs $850-$1,600 for a single residential swing gate, and we’ll tell you which one your gate actually needs before quoting.

Control Board and Limit Switch Diagnosis

When the opener clicks but the gate doesn’t move, our first test is the board’s output to the motor. On Linear and Viking units in Converse, we frequently see boards that have been killed by a gate binding against a heaved post, so the board fries itself trying to finish a cycle. Replacing the board without fixing the bind just burns the new board too.

Photo-Eye and Safety Loop Repair

Converse homes often have photo-eyes mounted on wooden posts that have warped out of alignment, which makes the gate reverse mid-cycle. We realign the sensors, repair corroded steel hinge straps, and rerun low-voltage wiring in proper conduit where the old landscape wire has dry-rotted under the Texas sun.

Trusted Brands We Service in Converse

Our Converse crews carry common boards, limit switches, and photo-eyes for FAAC, BFT, Linear, and Viking, so a repair on a Converse gate usually finishes the same visit rather than waiting on a parts drop. We don’t stock generic knockoffs. If your operator is a FAAC swing arm that was installed in 2011, our tech knows that unit’s failure points without guessing. We service what families in Converse actually own, and we keep the parts shelf organized around those brands.

Common Electric Gate Repair Problems We See in Converse Homes

• Manual gates retrofitted without dedicated power. The builder put in a cedar swing gate in 2005 with no 120V run at the gate line. Years later an opener was bolted on and plugged into an extension-cord-grade line. The operator starves, faults, and eventually burns out the board. We rerun power and low-voltage in real conduit so the opener gets clean current.
• Hinge post heave on Blackland Prairie clay. Converse sits on expansive clay that swells after spring rain and shrinks in drought. That cycle tilts shallow 2000s-era post footings, binding the gate against the ground and forcing the operator to work against the resistance. Reset the post, then the opener runs clean.
• Corroded steel hinges after San Antonio-area ice events. Infrequent but severe ice adds sudden stress to already-warped wooden frames and rusted steel hinges. The gate sags, the photo-eyes fall out of alignment, and the operator reverses every cycle.
• Block-wide simultaneous failure in tract-home subdivisions. Because Converse’s 1998-2012 homes went in block-by-block with the same builder shortcuts, gate failures cluster. When one house on a street off FM 1516 has a dragging gate, the neighbors’ shallow footings are usually already tilting and weeks from the same repair.

Pricing for Electric Gate Repair in Converse, TX

We Also Serve Cities Near Converse

Beyond Converse, our crews cover Universal City, Schertz, Cibolo, and the San Antonio neighborhoods that border Converse’s east side. Dispatch and scheduling are coordinated from the brand’s San Antonio office, and our technicians arrive in Converse with the parts and tools already loaded for the job you described on the phone.

FAQs About Electric Gate Repair in Converse