Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Angleton, TX
Gate work in Angleton runs on two tracks. In town, we handle ornamental driveway gates and automatic openers on ranch-style homes where the soil moves with every wet-dry cycle. Outside city limits, the calls shift to heavy pipe gates on acreage, cattle entries, and swing hardware that gets worked hard every single day. This is Brazoria County, and the black Beaumont clay under Angleton does not sit still. Gates that were plumb in May are leaning by August, and hinges that moved smoothly last year are seized with rust from Gulf humidity that rarely drops below 80%. If your gate is binding, dragging, or refusing to latch, call us at (626) 649-4572 and we’ll get a technician out to look.
Why Angleton Homes Are Different
Angleton sits at the county seat of Brazoria County, a landscape shaped by ranch land and the Gulf Coast’s low elevation. The soil is the defining factor in nearly every gate job here. Expansive black Beaumont clay soaks up water during wet spells and swells, pushing gate posts up and out of their footings. When the ground dries, the clay contracts and the posts tilt. We see this cycle repeat season after season, especially on the county road corridors east and south of town where drainage is slow and the clay runs deep. A post that has risen an inch may still hold a light ornamental gate for a while, but a heavy steel pipe gate on the same post will sag, drag, and eventually refuse to close.
The housing stock adds another layer. Near downtown, Angleton has older mid-century wood-frame homes with narrow driveways and gates that have been re-hung and re-welded over decades. At the edges of town and on the county roads, properties spread out: ranch-style homes on big lots, working ranches, and semi-rural acreage with tubular steel gates that see daily use from trucks, tractors, and livestock. Hardware wears out faster out there. Hinges gall, latch pins snap, and the weight of a 16-foot pipe gate eventually bends a post that was never set deep enough for the clay. We plan for all of it.
Hurricane Harvey left a mark on Angleton that still shows up in gate frames. The 2017 rainfall saturated Brazoria County soils beyond anything the clay could absorb, and the swell-and-shrink cycle that followed heaved thousands of posts out of plumb. Local technicians learned to expect the pattern: after any major flood or sustained wet period, posts along low-lying county roads rise, then lean inward as the clay dries. Re-setting posts and re-hanging gates in those clay-heavy zones is now a predictable part of gate work in Angleton, not a surprise.
Our Main Angleton Services
Angleton homeowners call us most about two things: gates that have stopped working after years of Gulf humidity and clay movement, and new gates built for how this soil actually behaves. Here’s what each service covers in Angleton.
Gate Repair in Angleton
Repair work in Angleton usually starts with a gate that drags on one side or won’t latch at all. We find bent hinge pins, rusted-through post mounts, and latch strikes that have drifted half an inch out of alignment as the clay under the post shifted. On pipe gates outside town, we see cracked welds and stretched chain-link tension bands from daily ranch use. We quote a written price before any work begins, then re-set the post if needed, replace the worn hardware, and re-hang the gate so it swings cleanly. We service FAAC, BFT, and Linear openers when the issue involves the gate itself. See Gate Repair in Angleton for the full breakdown.
Gate Installation in Angleton
A new gate in Angleton has to be built for the clay, not just for the opening. We set posts deeper than standard practice in dry soil, and we recommend heavier post gauge for long pipe gates on county roads where the ground heaves every wet season. For in-town driveway gates, we take care to match the style of the house, whether it’s a mid-century bungalow near downtown or a ranch-style home on the edge of town. We measure, order, and schedule every installation with a written price up front, never a surprise at the end. Details are on the Gate Installation in Angleton page.
Electric Gate Repair in Angleton
Automatic openers in Angleton fail in predictable ways. Humidity corrodes control board connections, ants build nests inside operator housings, and clay movement throws the photo-eye alignment out by half an inch, which stops the gate from closing. We troubleshoot the full loop: opener, safety edges, receiver, and limit switches. When we work on an electric gate inside the property, our technicians wear shoe covers and lay drop cloths before stepping inside, and they photograph the clean-up before they leave. This is electric work with the brand-specific training to match. Read more at Electric Gate Repair in Angleton.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Angleton
Our technicians are factory-trained on the brands Angleton homes and ranches actually use: FAAC, BFT, Linear, and Viking, among others. We stock common parts for these systems, which keeps repair turnaround shorter in Brazoria County than waiting on a distributor. Check our brands for the full equipment list.
Pricing for Gate Company in Angleton, TX
| Service | Typical range in Angleton |
|---|---|
| Gate latch repair or replacement | $120 – $395 |
| Gate hinge repair or replacement | $150 – $450 |
| Gate post re-setting (clay-heaved post, including concrete) | $350 – $1,200 |
| Gate frame straightening or weld repair | $200 – $600 |
| Gate opener troubleshooting and diagnosis | $90 – $200 |
| Gate opener circuit board replacement | $250 – $650 |
| Gate opener arm or actuator replacement | $350 – $850 |
| Photo-eye or safety sensor replacement | $150 – $350 |
| Full automatic gate installation (opener, posts, gate) | $4,200 – $12,800 |
| Driveway gate installation (steel or ornamental) | $2,800 – $9,500 |
Prices in Angleton push toward the higher end when a post has heaved badly in the clay and needs to be re-set deeper, or when a pipe gate outside town needs weld work along with new hardware. Every quote is written and agreed to before we start anything, and there’s no pressure to accept it.
Neighborhoods We Serve in Angleton
We work across Angleton and the surrounding county roads, from the older streets near downtown to the ranch properties east and south of town. Our standard response window for Angleton calls is same-day or next-day, depending on the time of the call and the parts involved.
- Downtown Angleton and the mid-century streets around the county courthouse
- The ranch-style subdivisions along Highway 288B and Wilburn Road
- County Road corridors east and south of town, including the clay-heavy zones toward the Brazos River
- Working ranch properties and acreage along FM 523 and Highway 35
- Residential areas near Angleton High School and the fairgrounds
Service Area – Cities Near Angleton
We serve Angleton and the surrounding Brazoria County communities. Homeowners in Lake Jackson, TX, Clute, TX, Freeport, TX, and Alvin, TX call us for the same clay-soil gate problems, and our crews work these areas on the same schedule. Dispatch and scheduling are coordinated from our Dallas-Fort Worth office, but the technicians who come to your gate are local to this area.
Serving Angleton, TX - Our Local Coverage Area
We’re based in the Angleton area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Angleton
Most Angleton calls get a same-day or next-day visit, depending on when you call and what parts the job needs. We answer the phone live around the clock, so a late-night call goes to a person, not voicemail. Call (626) 649-4572 and we’ll give you a straight answer on timing for your address.
For most repairs and replacements, no permit is needed in Angleton. New automatic gate installations with electrical runs may require a city or county electrical inspection, and we handle the paperwork side of that when it applies. We’ll tell you at the quote stage if your job needs any permitting.
We do. Many of our Angleton-area jobs are on county roads and ranch properties outside city limits, where the clay is deepest and the gates are heaviest. If you’re within reasonable driving distance of Angleton in Brazoria County, call us and we’ll confirm coverage.
If your gate is dragging, leaning, or refusing to open, call Latch & Post Gate Repair at (626) 649-4572 for a free estimate. We’ll give you a written price before any work starts, and we’ll leave your property the way we found it: clean floors, no surprises, and a gate that works right.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Angleton Customers Say
"Gate motor died and they replaced it carefully, cleaning every bit of debris off the driveway. Mindful not to leave the yard open with our dog out. Great crew."
- Benson Ide"The gate screeched and dragged. They fixed the track and oiled it, and wiped down everything after so there was no mess. Quiet and kind, in and out without any fuss."
- Opal Reddick"Our gate opener quit and they came out quick. The tech was careful not to leave the yard open while our dog was out, which I really appreciated. Clean work, swept up the metal shavings."
- Eleanor Boggs