Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in San Bruno, CA
Latch & Post Gate Repair is the San Bruno gate company families call when a hinge tears loose, a post leans, or an electric opener refuses to close. San Bruno sits in the San Bruno Gap, a break in the Coast Range that funnels Pacific wind across the peninsula harder than almost anywhere else in the county. That single fact reshapes nearly every gate job here. Gates rack, hinges shear, latches corrode, and openers trip their obstruction sensors from wind pressure alone. You’ll reach a live person at (626) 649-4572 any hour, and every job starts with a written price before we touch a tool.
Why San Bruno Homes Are Different
Most of San Bruno’s residential streets were built between the 1940s and 1960s, which means the typical driveway gate hangs on a post set in an original concrete pad that was never meant to hold a motorized opener. Decades of wind load cycling through the Gap have slowly worked those posts loose. In the flat neighborhoods east of El Camino Real, technicians routinely find posts that have heaved or tilted enough that a simple hinge swap becomes a full post-reset once the gate comes off.
The dual salt exposure doesn’t help. Marine layer rolls in from the Pacific on one side and bay humidity pushes in from the other, so zinc-plated hinges and steel post bases rust out years faster here than in sheltered cities a mile away. Hardware that lasts 15 years in Burlingame may show serious rust failure in 8 to 10 years in San Bruno. The Crestmoor neighborhood is the exception, rebuilt with newer gate infrastructure after 2010, sitting block-by-block next to untouched mid-century homes. Our crews quote for what’s actually under the paint, not what a generic estimator assumes.
Our Main San Bruno Services
Most San Bruno calls come down to two things: a gate that won’t hold or a gate that won’t move. Here’s how we handle each one here.
Gate Repair in San Bruno
Wind-driven failures dominate repair calls in this city. Frames rack out of square, hinge screws strip from overstressed wood, and latch hardware corrodes from the salt air. We work on Gate Repair in San Bruno jobs with a specific order of operations: assess the post first, because a leaning post means hinge replacement alone won’t last. We quote the full fix in writing before work starts, including any post-reset, so the scope doesn’t grow midway through the job.
Gate Installation in San Bruno
New gates in San Bruno have to be built for wind. That means heavier post footings, reinforced hinge points, and hardware chosen for salt-air exposure rather than the cheapest galvanized option. For Gate Installation in San Bruno, we measure the existing opening, check the condition of the current posts and concrete, and write a quote that covers the gate, the hardware, and any post work the site actually needs. No surprises on install day.
Electric Gate Repair in San Bruno
The Gap’s steady wind creates a failure pattern you rarely see in calmer cities: openers that cycle endlessly because gusts trip the obstruction sensor. The opener thinks something is in the way, reverses, and repeats. Electric Gate Repair in San Bruno often comes down to adjusting sensor sensitivity, reinforcing the gate frame so it doesn’t flex, and replacing control boards damaged by repeated cycling. We service openers from LiftMaster, FAAC, BFT, and the other brands families actually own, and we bring common parts stocked for San Bruno conditions on the first visit.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in San Bruno
Our technicians are factory-trained on our brands, including Linear, Viking, Ghost Controls, and DoorKing openers and hardware. Because San Bruno’s salt air and wind accelerate wear, we keep the most common replacement arms, sensors, and control boards stocked locally, so a repair often wraps up in a single visit when supply lines are moving normally.
Pricing for Gate Company in San Bruno, CA
These ranges reflect what we typically see on San Bruno jobs. The number in your written quote is the number you’ll pay – it’s agreed before any work starts, with no pressure to accept.
| Service | Typical range in San Bruno |
|---|---|
| Gate latch replacement | $180 – $340 |
| Hinge replacement (residential) | $220 – $450 |
| Gate post reset | $400 – $900 |
| Wood gate repair and realignment | $300 – $800 |
| Driveway gate opener repair | $350 – $800+ |
| Sensor alignment and safety check | $150 – $350 |
| Electric gate opener installation | $1,500 – $3,500+ |
| New driveway gate installation | $1,800 – $4,500+ |
Two things push a San Bruno quote toward the upper end of these ranges: a post that needs resetting before new hardware goes on, and rust damage that makes clean removal take longer. Neither gets discovered after the fact. You’ll see the line items before we order a single part.
Neighborhoods We Serve in San Bruno
We work throughout San Bruno, from the older mid-century blocks east of El Camino Real up into the Crestmoor hills and across the western side near the Gap. Our typical scheduling window for most San Bruno calls is within a few business days, and we keep routes coordinated with a Bay Area dispatch office so a technician can reach your street without a long wait.
- Crestmoor
- Huntington Park
- Portola Highlands
- Rollingwood
- East San Bruno
Service Area – Cities Near San Bruno
When a crew is already scheduling work in San Bruno, it’s straightforward to extend to neighboring communities along the Peninsula. We also serve Millbrae, CA, South San Francisco, CA, Pacifica, CA, and Brisbane, CA. Each one gets the same written price and C.A.R.E. care routine on every visit.
Serving San Bruno, CA - Our Local Coverage Area
We’re based in the San Bruno area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in San Bruno
Most straightforward gate replacements on existing posts don’t require a permit, but San Bruno may require one when new posts go in, when the gate is motorized, or when work extends past the property line. We can tell you what applies to your specific project during the estimate, and we’ll note the answer in your written quote.
Yes, and it’s the single most common cause of gate failure here. Constant wind pressure flexes frames, works post footings loose over time, and trips electric opener obstruction sensors repeatedly. A gate that would last years in a sheltered city needs real reinforcement in San Bruno.
For most repairs, we can usually schedule within a few business days. Emergency calls, like a gate that won’t close and leaves a yard open to the street, are handled on a priority basis. Call us and you’ll speak to a live person who can look at the schedule and give you a straight answer.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What San Bruno Customers Say
"Our gate opener quit and they came out quick. The tech was careful not to leave the yard open while our dog was out, which I really appreciated. Clean work, swept up the metal shavings."
- Eleanor Boggs"New hinges welded on a heavy gate. They laid down protection so no sparks hit the driveway and cleaned every bit after. Respectful of the property and the result is solid."
- Derek Pulanco"Electric gate was acting up. He was calm and methodical, found the bad sensor, and tidied the whole area by the gate post when he finished. No grease left on the driveway."
- Ravi Menon