Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Gig Harbor
Gate repair in Gig Harbor usually comes down to one of two things: a hinge post that has settled into the peninsula’s clay-heavy soil, or an operator that marine moisture has finally gotten to. We see both every week, from Harbor Hill to Canterwood. If your gate is sagging, binding, reversing mid-travel, or refusing to close, call (626) 649-4572 and a live person answers, day or night. We send a background-checked, uniformed technician to Gig Harbor who will hand you a written price before any work begins.
Why Latch & Post Gate Repair Is Gig Harbor’s Preferred Gate Repair Company
We are a Cedarwell-family gate specialist, and that means we work on gates all day, every day. Not fences. Not decks. Gates. The latch that holds the gate, the post that carries it, the operator that swings it, and the wiring that powers it. When a Gig Harbor customer calls us about a Viking operator that stopped mid-swing or a sagging hinge post near the historic waterfront, we know the failure mode before we pull into the driveway because we have seen it a hundred times on this side of the Narrows.
Every job carries the 365-Day Done Right Promise. If the repair is not right, we make it right. No argument, no fine print. Our technicians wear shoe covers and lay drop cloths before stepping inside your home, and they photograph the cleanup before they leave. That is the Cedarwell C.A.R.E. routine: clean up like it is our own home, ask before we move or touch anything, respect your quiet hours, and explain the price before the work. Cody Beckman set that standard, and every technician we send to Gig Harbor follows it.
We coordinate Gig Harbor scheduling from our Seattle office, but the crews who show up know the peninsula. They know the post-2007 subdivisions, the older waterfront properties, and the steep driveways that make gate work here different from Federal Way or Lakewood. That local knowledge is why Gig Harbor homeowners call us first when a gate stops behaving.
Metal Gate Repair in Gig Harbor
Metal gate repair in Gig Harbor almost always starts with the post. Most post-2007 master-planned communities on the peninsula used ornamental iron gates that were hung as manual gates, so the hinge post was never sized to carry an automated swing. Years of marine air and roughly 55 inches of rain have corroded the hardware, and the uphill post has often settled into the clay-heavy soil, putting the whole gate out of square. Our Gate Repair team corrects the post footing first, then addresses the hinge hardware, latch, and any weld or rust damage.
A typical metal gate hinge and post correction in Gig Harbor runs $350 to $850, depending on how far the post has moved and whether we need to reset the footing in concrete. Rust repair and re-welding on ornamental iron gates typically runs $200 to $600 per section. You will see the exact number in writing before we touch anything.
Hinge, Post, and Realignment Work
When an iron gate drags on its latch side or will not stay closed, the hinge post is usually the culprit, not the gate itself. We pull the post back to plumb, reset the footing where the clay soil has shifted, and re-shim the hinges so the gate swings clean.
Weld and Rust Repair
Salt-laden air off Puget Sound keeps exposed iron damp for weeks at a time. We grind out rust pockets, re-weld cracked joints, and treat the bare metal before repainting. The goal is a repair that looks like it belongs, not a patch job.
Wood Gate Repair in Gig Harbor
Wood gate repair in Gig Harbor has its own seasonal rhythm. Cedar-board gates on older waterfront properties and in neighborhoods like Harbor Hill and along Rosedale Street absorb harbor fog and rain from October through February, swell up, and then the latch binds or the gate will not close completely. Once the wood dries out in spring, the gate often settles back to square, but by then the latch has been strained and the hinges may have pulled. We repair the frame, re-hang the gate, and adjust or replace the latch so it works through the wet season instead of fighting it.
Most wood gate frame and latch repairs in Gig Harbor run $250 to $600. If the gate has sagged enough to require a frame re-square and new diagonal bracing, expect $400 to $900. We quote a written price before we start, and we can schedule around nap time if quiet matters in your house.
Seasonal Swell and Latch Binding
When a cedar gate will not latch from November through February but closes fine in July, the wood is moving. We plane or adjust the latch plate, tighten the hinges, and sometimes add a mid-rail brace to keep the gate from twisting as the wood expands.
Sagging Frames and Hinge Pull-Out
A wood gate that drags on the ground at the latch side has usually lost its frame integrity. We pull the gate, re-square the frame, and re-set the hinges with longer screws or through-bolts into solid wood. The fix should hold for years, not months.
Trusted Brands We Service in Gig Harbor
Our technicians are factory-trained on the brands Gig Harbor families and HOAs actually run: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That training matters because a FAAC hydraulic operator fails differently than a Viking swing arm, and diagnosing it correctly the first visit saves you money. We keep common parts stocked for Gig Harbor jobs, so a typical operator repair does not mean waiting a week on a shipped part. When your HOA gate on a post-2007 subdivision opens and closes all day, the operator brand is only part of the story; the post footing and the power run are usually the rest.
Common Gate Repair Problems We See in Gig Harbor Homes
- Post-2007 gates installed manual and unpowered. Production builders on the peninsula hung ornamental iron and cedar-board gates without conduit, loop detectors, or operator brackets. Retrofitting automation means solving all three before the operator gets mounted.
- Operators binding against settled hinge posts. Steep driveways and clay-heavy soil cause the uphill post to lean, which twists the gate leaf and makes the operator arm fight the geometry until the motor burns out.
- Marine corrosion on boards and wiring connections. Harbor fog and salt air keep exposed terminals damp for weeks. Circuit boards corrode, limit switches fail, and hardware seizes faster than in inland Pierce County.
- Cedar gates swelling every winter. Older waterfront properties with wood-panel gates see seasonal warp from October through February, causing latches to bind and automated gates to reverse mid-travel or refuse to close fully.
Pricing for Gate Repair in Gig Harbor, WA
Here are the ranges we quote most often on the Gig Harbor side of the Narrows, and they always come as a written price before work starts, never as a verbal ballpark that changes later.
- Gate realignment and hinge adjustment: $180-$450
- Hinge post reset and footing correction: $350-$850
- Latch or lock replacement: $150-$400
- Operator repair (board, arm, or limit switch): $325-$950
- Wood gate frame repair and re-hang: $250-$900
- Full automation retrofit on a manual gate: $2,200-$5,800 (includes post footing, conduit, operator, and safety edges)
What moves the number is the post. If the footing has settled and the post needs resetting, that adds real labor. If the gate was never wired for power, the trench and conduit run add more. A free estimate from Gig Harbor gets you the exact figure, in writing, before you decide anything. Call (626) 649-4572 and we will schedule it.
We Also Serve Cities Near Gig Harbor
Our crews handle gate work throughout the peninsula and across the Narrows. In addition to Gig Harbor, we regularly serve Wauna, Vashon, Port Orchard, and University Place. If you are in one of those areas and need a gate that actually closes, call (626) 649-4572 and we will get you scheduled.
Serving Gig Harbor, WA - Our Local Coverage Area
We’re based in the Gig Harbor area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Gig Harbor
Before an operator gets mounted, we have to confirm the hinge post footing can carry the load, run conduit for power and safety wiring, and install a loop detector or photocells if your driveway layout calls for them. In post-2007 Gig Harbor subdivisions, most manual gates were hung without any of that. The operator itself is the last step, not the first. Call (626) 649-4572 for a free on-site look at your gate and a written retrofit plan.
Two reasons working together: marine moisture and post settlement. Harbor fog and salt-laden air keep exposed wiring connections and circuit boards damp for weeks at a time, which corrodes them faster than in drier inland cities. At the same time, the peninsula’s clay-heavy soil and steep driveways cause hinge posts to shift, which makes the operator arm bind against a gate that no longer swings true. The motor works harder, runs hotter, and fails sooner than the same unit would in Lakewood.
On a cedar or wood-panel gate, the likely cause is seasonal swell. From October through February, Gig Harbor’s rain and fog push moisture into the wood, the gate leaf grows slightly, and the latch or the close limit reads that as an obstruction, so the operator reverses. We adjust the latch plate, re-shim the hinges, and sometimes re-set the operator’s close limit to account for the seasonal movement. Call (626) 649-4572 and we will sort it out before the wet season peaks.
Yes. We are factory-trained on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, which covers most of the operator brands installed on Gig Harbor HOA entry gates and private driveways. We keep common replacement parts stocked for these brands, so a typical board or limit switch repair does not mean waiting on a special order. Tell us the brand and what the gate is doing, or not doing, and a live person will get you a service window.
They need a more careful post footing and often a longer operator arm or different mounting geometry. A gate installed on a slope is fighting gravity every time it swings, so any settlement in the uphill post translates directly into operator strain. We correct the post first, then mount the operator so it is not pulling against a twisted hinge line. A flat-ground install would never see that failure mode, which is why crews from flatter markets miss it, but it is routine for us in Gig Harbor.
If your gate is sagging, binding, corroded, or wired wrong, call (626) 649-4572. We will send a technician who knows Gig Harbor, hands you a written price before touching anything, and leaves your property cleaner than they found it. That is the whole job.
Written by Cody Beckman, Owner at Latch & Post Gate Repair, serving Gig Harbor as part of the Cedarwell family since 2009.