Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Coppell
Gate repair in Coppell usually starts with a phone call about a sagging hinge post or an opener that groans before it moves. We’re Latch & Post Gate Repair, part of the Cedarwell family, and we’ve been working exclusively on gates since 2009. Our techs know Coppell’s neighborhoods, its HOAs, its soil, and its 1990s-era wrought iron. When you call (626) 649-4572, a live person answers, day or night, and we’ll give you a written price before any work begins. No voicemail queues. No vague estimates. Just a straight answer about what’s wrong and what it costs to fix it.
Why Latch & Post Gate Repair Is Coppell’s Preferred Gate Repair Company
Cody Beckman leads our team, and the standard he set is simple: treat every Coppell home like we’d treat our own. That means shoe covers before we step inside, drop cloths under the work area, and a photo of the cleanup before we leave. It also means we explain the price in writing before touching a single bolt.
Coppell families call us because we show up on time and we don’t rush. We know the Northlake Woodlands original gates, the Cottonwood Creek keypads, and the commercial slide gates along Belt Line Road near DFW Airport. When a gate fails, you want someone who’s seen that exact failure fifty times before. That’s us.
Every repair and installation we do is covered by the 365-Day Done Right Promise. If it’s not right, we make it right. No argument, no fine print.
Sliding Gate Repair in Coppell
Sliding gate repair in Coppell is common on the wider lots where a swing gate would eat half the driveway. These gates roll on a track and carry their weight on rollers, and when the Blackland Prairie clay under the track heaves after spring rains, the gate starts to bind, screech, or stall mid-travel. A sliding gate that fights its motor is a sliding gate that’s about to burn out a gearbox.
We service the full slide assembly: track, rollers, guide posts, chain or belt drives, limit switches, and the operator itself. Most sliding gate repairs in Coppell run between $240 and $680 depending on whether we’re replacing rollers, realigning track, or swapping out the opener. You’ll see the exact number in writing before we start.
Track Realignment and Roller Replacement
When the track shifts, the gate doesn’t just get louder. It stresses the operator every cycle. We lift the gate, true up the track, replace worn rollers, and set the limit switches so the gate stops in the right spot every time.
Operator and Limit Switch Repair
FAAC and BFT operators are common on Coppell’s newer slide gates, and both brands are on our factory training list. If the motor runs but the gate won’t move, we check the drive first, then the board. Straight answer, written price, done.
Wrought Iron Gate Repair in Coppell
Wrought iron gate repair in Coppell is a particular specialty of ours because the city’s 1990s buildout left thousands of ornate double-swing iron driveway gates hitting the 20-30 year mark at the same time. The failure pattern is consistent: the hinge post shifts, the gate sags, the latch misses, and then someone leans on it and makes it worse.
We do post excavation and resets, hinge replacement, welding, rust treatment, and realignment. A typical hinge post reset on a wrought iron gate in Coppell runs $320-$780, and a full rebalance with hinge replacement usually lands between $450 and $950. We quote the job, not the hour.
Hinge Post Reset and Rebalance
The post is the gate. If it leans, the gate leans. We dig out the old footing, pour a new one, set the post to plumb, and rehang the gate so it swings without dragging. On Coppell’s expansive clay, we set posts deep enough to ride out the seasonal movement.
Weld Repair and Rust Treatment
Coppell’s iron gates develop rust at the weld points and along the bottom rail where irrigation spray hits. We grind out the rust, repair the welds, and treat the surface so the repair doesn’t peel in two seasons. If your HOA requires a specific finish, we’ll match it.
Trusted Brands We Service in Coppell
We’re factory-trained on the brands Coppell homeowners actually have: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That means we don’t guess at a wiring diagram. We stock common parts for FAAC, BFT, and Linear operators locally, so a capacitor or a set of photo-eyes doesn’t mean a week-long backorder. On older Mighty Mule and LiftMaster units with cracked keypad housings from winter ice storms, we keep replacement housings on the truck. The right part, the first visit. That’s the whole point of visiting often.
Common Gate Repair Problems We See in Coppell Homes
- Hinge post failure on 1990s ornamental gates. The original posts were set in soil that swells and shrinks with every season. After 25 years, the post leans, the gate drags, and the latch stops lining up.
- Mismatched openers on unbalanced gates. Lots of Coppell gates from the 90s had a cheap linear actuator bolted on years after the gate was built. The gate was never balanced for automation, so the operator works itself to death.
- Keypad and board damage from ice storms. DFW gets a hard freeze every few winters, and older LiftMaster and Mighty Mule keypads crack when water gets in and freezes. We replace the housing and the board, not the whole system.
- Photo-eye faults on automatic gates. In neighborhoods with kids and pets, the safety edge gets bumped, kicked, or chewed. A misaligned photo-eye means the gate won’t close. We realign or replace them every week in Coppell.
Pricing for Gate Repair in Coppell, TX
Here are real numbers for Coppell’s market. Hinge post resets run $320-$780. Sliding gate track realignment runs $240-$480. Operator replacement runs $550-$1,400 depending on brand and gate weight. Keypad entry repair runs $140-$310. Weld and rust repair runs $180-$450. These are honest ranges, not teaser rates.
What moves the price: post depth, gate weight, operator brand, and whether the HOA requires a specific finish or hardware. We give you a written price before any work begins, every time. Call (626) 649-4572 for a free estimate, and we’ll send someone out to walk the gate with you.
We Also Serve Cities Near Coppell
Our Gate Repair crews serve Coppell and the surrounding DFW communities. If you live just across the city line in Lewisville, Carrollton, Grapevine, or Addison, we’ll come to you with the same written-price policy and the same shoe covers on the floor. One call handles all of it.
Serving Coppell, TX - Our Local Coverage Area
We’re based in the Coppell area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Coppell
In most Coppell subdivisions, yes, if the repair changes the gate’s hardware, finish, or structural layout. Nearly every residential community in Coppell has covenants that govern gate material, color, and style, and many require an architectural approval letter before you swap hinges or change a post. We’ve worked with Coppell HOAs for years and can help you file the request. If the repair replaces like-for-like hardware with no visible change, approval is often waived. Call (626) 649-4572 and we’ll tell you what your specific HOA requires.
Because the panel isn’t the problem. The post is. Coppell sits on Blackland Prairie clay that swells after spring rains and shrinks in summer, and over 20 or 30 years that cyclical movement levers the hinge post out of plumb. Once the post leans, the gate will always sag, no matter how many times you tighten or replace the hinges. The fix is a post reset: dig out the old footing, pour new concrete, set the post plumb, and rehang the gate. Call us for a free look before you spend more money on the panel alone.
Yes, and it’s the soil. Coppell’s expansive clay heaves when it’s wet and contracts when it dries, which shifts posts and tracks just enough to knock the limit switches out of alignment on an automatic operator. It’s not a weak operator. It’s a moving foundation. We can set the limits and resynchronize the operator, but the longer fix is often a post reset or track stabilization so the gate stops moving under the motor.
Yes. We repair and replace keypads and circuit boards on older LiftMaster operators. Coppell’s winter ice storms crack keypad housings when trapped water freezes, and the board behind them often corrodes. We stock replacement housings and know which boards are still available for the models installed in Coppell’s 1990s-era homes. A keypad entry repair usually runs $140-$310, and you’ll have a written price before we start.
Yes. Automatic gates in Coppell must have functioning safety devices, typically photo-eyes and a reversing edge, to meet current standards and pass any city or HOA inspection. If your gate reverses on nothing or won’t close at all, a misaligned or failed photo-eye is usually the cause. We’ll test both, replace what’s bad, and confirm the gate reverses properly before we call it done. Call (626) 649-4572 to schedule a check.
Get Your Coppell Gate Fixed Right
If your gate is sagging, grinding, or not responding, call us at (626) 649-4572. We’ll answer, ask a few questions, and set a time to come look. The estimate is free. The price is written before any work begins. And when we leave, your floors are clean, your gate works, and you have a photo of the cleanup on your phone.
Written by Cody Beckman, Owner at Latch & Post Gate Repair, serving Coppell since 2009.