Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Glendale
Gate installation in Glendale usually costs between $2,800 and $11,000 for a standard residential driveway gate, and we typically schedule Glendale installs within 5 to 9 business days once the gate is fabricated or ordered. Custom wrought-iron work, which Glendale requests more than almost any city we serve, lands on the higher end of that range because of the fabrication time and the hardware needed to move a heavy panel. If you’re weighing a new gate for a Rossmoyne home or a hillside property in Chevy Chase Canyon, call (626) 649-4572 and we’ll walk through your options in plain terms. We cover the full Glendale area, from the flats north of the 134 to the canyon roads east of Brand Park.
Why Latch & Post Gate Repair Is Glendale’s Preferred Gate Installation Company
Glendale homeowners reach out to us for a specific reason: this city has a concentration of heavy, ornate entry gates that most general contractors don’t know how to hang properly. That’s why our Gate Repair - Glendale team specializes in these exact challenges. A hand-fabricated wrought-iron swing gate can weigh 600 to 900 pounds. If the hinge posts aren’t set deep enough or the operator isn’t matched to the gate’s weight, it sags, it scrapes, and it burns out motors. We correct those mistakes on a regular basis.
Every Gate Installation we do in Glendale starts with a written price. Before any work begins, you see the full number, line by line, and nothing gets added on unless you approve it first. Our technicians arrive in uniform, put on shoe covers before walking through your entry or into your home, and lay drop cloths where work happens. Before we leave, we photograph the cleanup so you can see exactly how the area was left. That routine is what the Cedarwell C.A.R.E. values are built around: Clean up like it is our own home, Ask before we move or touch anything, Respect the family’s time and quiet hours, and Explain the price before the work.
Our work in Glendale is covered by the 365-Day Done Right Promise. If the gate sags, drifts, or the operator acts up within a year, we come back and make it right. We don’t argue about fault. We just fix it. Cody Beckman, who leads Latch & Post, set that rule because a gate that doesn’t close properly stops being a gate.
Gate Fabrication in Glendale
Gate Fabrication in Glendale typically runs $3,500 to $14,000 depending on size, ornamentation, and whether the gate is a single swing, dual swing, or an automated sliding panel. Glendale’s housing stock drives this more than anything. The 1920s through 1950s Spanish Colonial and Craftsman homes in Rossmoyne and Adams Hill were often built with original wrought-iron gates that are now rusted through at the joints, and homeowners here don’t replace them with off-the-shelf panels. They commission reproductions that match the scrollwork on a 90-year-old gate, and we’ve fabricated more of those in Glendale than in Burbank and Pasadena combined.
Custom Iron and Steel Entry Gates
We build gates from steel stock, weld the frame, and hang the panel on posts set in concrete at the right depth for a heavy gate. A 14-foot dual-swing custom gate can weigh nearly half a ton, so the hinge posts need to be set below the soil’s expansion zone or they will tilt within two seasons. We quote the full job, including posts, hinges, finish, and operator, before cutting any steel.
Ornamental Gate Refabrication
When an original Glendale gate has sentimental or architectural value, we often cut out rusted sections and refabricate them to match. The scrolls, finials, and picket spacing are matched, not approximated. Then the whole panel gets blasted, primed, and top-coated so the repaired gate weathers the same as the rest. This kind of work usually lands between $1,800 and $6,000, depending on how much of the gate is salvageable.
Automatic Gate Installation in Glendale
Automatic Gate Installation in Glendale runs $1,800 to $7,500 for the operator, safety equipment, wiring, and intercom or keypad integration, added on top of the gate itself. Most Glendale families want the same thing: a swing or sliding gate that opens from a keypad or phone app and doesn’t wake a sleeping kid when it moves. That means a quiet, correctly sized operator, not the cheapest unit on the shelf.
Operators, Keypads, and Intercoms
We install LiftMaster, DoorKing, and Linear operators, and we pair them with keypads, camera stations, and video intercoms so you can see who’s at the gate from inside the house. For a bespoke wrought-iron entry like the one we hung in Rossmoyne, we matched a LiftMaster operator with a camera-and-intercom unit at the pedestrian walkway. The owner opens the gate from the house, sees the visitor on the panel, and doesn’t have to walk out to the sidewalk.
Cantilever and Hillside Systems
Chevy Chase Canyon and upper Glenoaks have driveways that exceed a 15% grade. Standard V-track slide gates don’t work there because the track gets buried in debris or the gate binds on the slope. We install cantilever slide systems instead, where the gate rides on rollers set above the ground, or we set dual-swing gates with hinges matched to the grade. These installs require more concrete work and usually run toward the higher end of the price range above.
Trusted Brands We Service in Glendale
Our technicians are factory-trained on the equipment Glendale homes actually use: LiftMaster, DoorKing, Linear, Viking, Ghost Controls, and more. We keep replacement arms, control boards, remotes, and photo eye sensors in local stock so a Glendale service call doesn’t stall while parts ship from out of state. If your existing operator is a DoorKing, we can usually service it or swap it for a compatible unit on the same visit. Not every gate company carries parts for both Linear swing operators and cantilever slide hardware. We do.
Common Gate Installation Problems We See in Glendale Homes
- Santa Ana wind damage to ornamental gates. When wind funnels through the Verdugo Mountain passes, it hits a large wrought-iron gate like a sail. Hinges bend, frame corners warp, and motors that were undersized to begin with strip their gears. We see this every fall in Glendale, and we size new gates and posts to handle it.
- Undersized posts that tilt within a season. Glendale’s dry summers and wet winters make the soil around gate posts expand and contract sharply. A post set in a shallow footing starts to lean, which throws the whole gate out of plumb and makes the operator fight the panel on every cycle. We set posts below the movement zone and use properly sized concrete collars.
- Slope-mismatched slide gate hardware. Hillside driveways in Chevy Chase Canyon and Brockmont regularly exceed a 10 to 15% grade. A level-grade slide gate with a V-track and rack-and-pinion system binds on the incline. The gate starts, stalls, and throws error codes. The fix is a cantilever system or a dual-swing layout, and we diagnose this on nearly every hillside install we take over.
- Custom gates installed without matching automation. A custom wrought-iron gate that looks beautiful but has an operator rated for half its weight will fail within a year or two. We often replace the operator and reinforce the hinge post at the same time, then calibrate the loop detector and photocells so the gate stops and reverses on command. Quiet operation matters too, especially when a gate sits below a bedroom window.
Pricing for Gate Installation in Glendale, CA
A single swing driveway gate in Glendale runs $2,800 to $6,500 installed, including posts, hinges, and a basic manual latch. A custom fabricated dual-swing gate with an automatic operator, keypad, and intercom runs $7,000 to $18,000. Cantilever slide systems on slopes add $1,500 to $4,000 for the concrete work and hardware. These are the real ranges we quote in this city. You get the exact number in writing before we start, and that number doesn’t change unless you change the scope. Call (626) 649-4572 for a free estimate.
We Also Serve Cities Near Glendale
Our Gate Installation in Glendale service area extends into the surrounding communities. We regularly install gates in Burbank, West Hollywood, Altadena, and Pasadena, and we schedule those jobs with the same written-price and cleanup routine we use in Glendale. If you’re just over the city line, call us and we’ll let you know when we can be there.
Serving Glendale, CA - Our Local Coverage Area
We’re based in the Glendale area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Installation in Glendale
Yes. We cut out rusted sections or build a full replacement panel that matches the scrollwork, finials, and picket spacing of your existing gate. Most custom gates take 3 to 6 weeks to fabricate and finish. Call (626) 649-4572 and we’ll measure, photograph the original, and give you a line-item price before any metal is cut.
Because your driveway grade exceeds what a level-grade slide gate can handle. On slopes over 10 to 15%, which are common in Chevy Chase Canyon and upper Glenoaks, the track collects debris and the rack-and-pinion system binds. You need a cantilever slide system or dual-swing gates. We install both, and the quote includes the concrete and hardware changes required.
Sometimes, but not usually. A sagging gate usually means the hinge post has shifted or the frame welds have failed. Straightening the panel without addressing the post is a temporary fix. We’ll inspect the post footing, the hinge welds, and the frame before we tell you what can be salvaged and what needs replacement. You’ll see the real number in writing either way.
At minimum, a new automatic gate should include photoelectric sensors across the opening, a reversing mechanism on the operator, and edge sensors if the gate closes against a wall or fence post. California building codes require entrapment protection on automated gates, and we install and test all of it as part of the job. A gate that doesn’t stop when a kid or dog runs through is not a finished job.
They really do. When wind funnels through the Verdugo passes and hits a broad ornamental gate, the lateral force is enough to bend hinges and warp the frame, especially if the gate was undersized at installation. We’ve replaced hinge posts and straightened panels on Glendale gates after nearly every major wind event in recent years. If you’re installing a new gate here, it should be built and anchored for that load. Call (626) 649-4572 to talk through what that means for your entry.
Written by Cody Beckman, Owner at Latch & Post Gate Repair, serving Glendale as part of the Cedarwell family since 2009.