Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Mission Bend, TX
Latch & Post Gate Repair is a Mission Bend gate company focused on one trade: the latch that holds the gate and the post that carries it. Most of our work here involves 25 to 40 year old HOA community gates and matching wrought-iron property gates on brick homes built between 1978 and 1995. These gates were installed when Mission Bend was first developed, and the combination of 90%+ summer humidity and standing water from the Addicks Reservoir watershed has been hard on them. If a gate in Mission Bend is sagging, stuck open, or dead at the control board, call (626) 649-4572 and we’ll give you a written price before any work starts.
Why Mission Bend Homes Are Different
Mission Bend is a dense cluster of 1980s and 1990s master-planned HOA subdivisions, and that changes almost every gate job. The community entrance gates were installed during the original build-out, which means the operators, loop detectors, and control boards are now reaching the end of their service life at roughly the same time. A technician who works Mission Bend regularly sees the same failures repeating across different subdivisions: corroded control boards, weld fatigue on original hinges, and posts that have shifted in heavy clay soil after decades of wet-dry cycles.
Hurricane Harvey left a mark here too. Many subdivision entry gate operators were submerged during the 2017 flooding, then dried out and put back into service rather than replaced. Years later, those control boards and motors are failing mid-cycle, leaving community entrances stuck open or closed. When we open a Harvey-era operator in Mission Bend, we expect corrosion on the low-mounted components and plan the quote accordingly. That history means gate repair here is often an HOA decision rather than a single homeowner call, so we’re used to walking board members through what failed, what it costs, and what can wait.
Our Main Mission Bend Services
Mission Bend homeowners and HOAs call us most for two things: repairing gates that have stopped working, and replacing gate equipment that’s too far gone to patch. Each service has its own Mission Bend page with specific pricing and details.
Gate Repair in Mission Bend
Repair work in Mission Bend usually starts with a full hardware check: hinges, latch, post alignment, and the weld points that fail first on 30-year-old wrought iron. The humidity here rusts hardware faster than in drier Texas cities, so a gate that still looks solid from the street may have a hinge pin nearly worn through. We quote the repair at a fixed price before we touch anything, and we carry the common Mission Bend hardware stock on the truck so most calls finish in one visit. Learn more on our Gate Repair in Mission Bend page.
Gate Installation in Mission Bend
New gate installation in Mission Bend means matching the existing subdivision look, because most of these communities have architectural guidelines and a board that reviews changes. We measure the opening, check the existing posts for plumb and rust, and write a full installation price that includes hardware, hinges, and cleanup. For HOA entrance gates, we coordinate with the board and property manager so the quote reflects what the community actually needs. Details and process are on the Gate Installation in Mission Bend page.
Electric Gate Repair in Mission Bend
Electric gate repair in Mission Bend is often about water. Ground-mounted operators sit low, and after heavy rain events like Harvey, submerged control boards and motors corrode from the inside. We diagnose the operator, loop detector, and safety edges, then give you a written repair price before we order parts. When a board is too far gone, we’ll tell you that plainly and quote the replacement. See the Electric Gate Repair in Mission Bend page for specifics.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Mission Bend
We’re factory-trained on the brands Mission Bend homes and communities actually run: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Most common parts are stocked locally, so a Linear or Viking board swap usually happens within the same week. See our brands for the full list.
Pricing for Gate Company in Mission Bend, TX
| Service | Typical range in Mission Bend |
|---|---|
| Gate latch replacement | $125 - $325 |
| Hinge replacement (set) | $150 - $400 |
| Wrought-iron weld repair | $100 - $300 per weld point |
| Post straightening / reset | $250 - $600 |
| Slide gate roller replacement | $180 - $450 |
| Gate opener control board replacement | $350 - $850 |
| Gate opener motor replacement | $400 - $950 |
| Loop detector replacement | $250 - $550 |
| Safety edge / photocell replacement | $200 - $450 |
| Full wrought-iron gate installation | $1,500 - $5,000+ |
In Mission Bend, the biggest price driver is corrosion. A gate that needs a simple hinge swap in a drier city may need post work or weld repair here because the humidity and standing water have eaten at the metal. You’ll see the full written price before we start, every visit, with no pressure to accept.
Neighborhoods We Serve in Mission Bend
We work throughout Mission Bend, from the HOA-governed subdivisions along Bellaire Boulevard to the quieter residential streets near the Addicks Reservoir edge. Our typical response time for the Mission Bend area is same-day or next-day for repair calls, with installation work scheduled around HOA review timelines.
- Mission Bend subdivisions along Bellaire Boulevard
- Communities near Addicks Reservoir
- HOA neighborhoods west of Highway 6
- Residential streets north of Beechnut Street
- Subdivisions around the Mission Bend golf course area
Service Area – Cities Near Mission Bend
Latch & Post Gate Repair is part of the Cedarwell family of independently owned and operated gate specialists, with dispatch and scheduling coordinated from the brand’s Houston office and crews serving Mission Bend locally. We also work in nearby Houston, TX, San Antonio, FL, Dallas, TX, and Fort Worth, TX. If you’re just outside the Mission Bend area, call and we’ll confirm coverage.
Serving Mission Bend, TX - Our Local Coverage Area
We’re based in the Mission Bend area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Mission Bend
Repair calls in Mission Bend are typically same-day or next-day. If an HOA entrance gate is stuck open or closed, call (626) 649-4572 and we’ll give you an honest arrival window. Installation and new automation work is scheduled after we measure and quote.
Most Mission Bend subdivisions require board or property manager approval before entrance gate work begins. We provide the diagnostic detail and written quote your board needs to make a decision, and we’re comfortable walking them through it. Call (626) 649-4572 for a free estimate.
Yes. We repair and install matching wrought-iron property gates on individual Mission Bend homes, and we work on subdivision entrance gates with the HOA or property manager. Every visit starts with a written price, and our technicians wear shoe covers and lay drop cloths when the job takes us inside.
Call Latch & Post Gate Repair at (626) 649-4572 for gate work in Mission Bend. A live person answers around the clock, and we’ll give you a written price before any work begins.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Mission Bend Customers Say
"Electric gate was acting up. He was calm and methodical, found the bad sensor, and tidied the whole area by the gate post when he finished. No grease left on the driveway."
- Ravi Menon"Gate motor died and they replaced it carefully, cleaning every bit of debris off the driveway. Mindful not to leave the yard open with our dog out. Great crew."
- Benson Ide"The gate screeched and dragged. They fixed the track and oiled it, and wiped down everything after so there was no mess. Quiet and kind, in and out without any fuss."
- Opal Reddick