Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Fern Park
Gate repair in Fern Park comes down to two things: understanding what Seminole County’s building department expects, and knowing what the summer storms do to the gate electronics along US-17-92. We work on both sides of that every week. If your gate is sagging on cracked concrete posts, dead after a lightning strike, or stuck halfway and groaning, call us at (626) 649-4572, and a live person answers. We’ll schedule a technician for Fern Park, and you will get a written price before any work starts.
Why Latch & Post Gate Repair Is Fern Park’s Preferred Gate Repair Company
We are part of the Cedarwell family of independent gate specialists and have been repairing gates since 2009. Our focus is narrow: gate repair, gate installation, and electric gate repair. That is all we do. The technician who arrives at your Fern Park home is background-checked, uniformed, and factory-trained on the brands most common in this area, including Viking, Ghost Controls, and DoorKing.
Fern Park homeowners repeatedly tell us the same thing: other contractors quote a motor swap, ignore the permit, and never mention that the original 1970s concrete post cannot handle a modern operator’s torque. We start with the post and the hinge before we ever recommend a motor. Every visit includes shoe covers, drop cloths inside the home, and a photo of the cleanup before we leave. That is the Cedarwell Care Promise, and it is not optional.
Sliding Gate Repair in Fern Park
Sliding Gate Repair in Fern Park most often means a heavy steel gate on a track, usually at a manufactured-home community entrance off US-17-92 or at a private driveway in one of the older subdivisions. The gate rolls on wheels or a cantilever system, and the most common problems we see are bent or rusted tracks, worn rollers, a damaged rack and pinion, or a control board that a storm surge has cooked. A basic roller replacement runs $150 to $350. Replacing a bent track section typically costs $400 to $800 depending on length. A control board replacement on a Viking or DoorKing operator runs $280 to $650 for the part, plus labor. You will see the exact number in writing before we touch anything.
Track and roller service
Gates that grind, jerk, or stop halfway along the track usually have worn wheels or a track that has shifted in the soft ground. Fern Park’s high water table lets concrete track pads settle and tilt, and the gate then drags on its rollers. We lift the gate, replace the wheels, re-level the track pads, and adjust the limit switches. On most sliding gates, this is a two-to-three-hour job, and the gate runs quieter after than it did when new.
Lightning-surge and control-board failure
Central Florida’s storm season delivers some of the highest lightning-strike densities in the country, and Fern Park’s flat, low-lying position makes unprotected gate circuits an easy target. When a surge travels through the conduit and destroys the control board, the gate goes dead with the operator still holding power. We replace the board and add surge suppression so the next storm does not do the same thing. The surge retrofit is typically $120 to $240 in parts, installed as part of the repair.
Wrought Iron Gate Repair in Fern Park
Wrought Iron Gate Repair in Fern Park focuses on ornamental steel or iron gates, often at the entrance to a 1970s or 1980s subdivision, a side yard, or a pool enclosure. The iron itself is usually fine; what fails is the hardware around it. Hinges corrode, welds crack under repeated opening and closing, and the gate droops until the latch no longer lines up with the post. Replacing a set of heavy iron hinges runs $180 to $400. Welding a cracked joint costs $150 to $350 per joint depending on access and thickness. If the post itself is rusted through at the base, a full post replacement with a proper concrete footing runs $600 to $1,200 in Fern Park. That price includes the Seminole County permit, which most contractors do not mention until after the work is done.
Hinge and sag correction
A wrought iron gate that scrapes the driveway is not a motor problem; the hinge post has moved or the hinges have worn. We saw this recently at a manufactured-home community off US-17-92: the aging slide gate’s hinge post had sagged so badly that the new rack and pinion would have bound within a month. The correct fix was reinforcing the footing first, then squaring the gate to the post. We do the same on ornamental iron gates: correct the alignment, then adjust the latch and closer.
Welding and rust repair
Fern Park’s humidity and rain cycle rust through the bottom rails and hinge plates on older wrought iron gates faster than you would expect. We cut out the rotted section, weld in new steel, grind it flush, and prime and paint the repair. Where the rust has gone too far into a hinge mount, we replace the hinge entirely rather than patch it and hope. The goal is a gate that swings true and does not need shims or washers to close.
Trusted Brands We Service in Fern Park
We are factory-trained on the operators that Fern Park homeowners and community boards actually run: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Most service calls here involve Viking or DoorKing slide operators on shared entrances, and Ghost Controls on private driveway gates. Because we stock common control boards, receivers, and limit switches for those brands, a Fern Park repair often does not wait on a parts shipment. If we do not have the part on the truck, we tell you exactly when it arrives and what it costs before we order.
Common Gate Repair Problems We See in Fern Park Homes
- Lightning-surge burnout of control boards. Unprotected circuits along US-17-92 take surges every storm season. The board dies, the gate freezes, and the fix is a board replacement plus a surge retrofit.
- Corroded buried conduit and wiring. Fern Park’s high water table and seasonal standing water rust through underground conduit and shorten low-voltage wiring. The gate opener loses power or the safety sensors fault out for no visible reason.
- Cracked and undersized original posts. Many 1960s and 1970s gate posts were poured too small or built from hollow block. A modern operator’s torque flexes and cracks them, which no motor swap will ever fix.
- Sagging hinges and misaligned latches. Wrought iron and tubular steel gates settle over time, especially with the soft, wet ground under Fern Park footings. The latch stops catching, or the gate scrapes the concrete.
Pricing for Gate Repair in Fern Park, FL
We quote every Fern Park job as a flat, written price before work begins. No hourly meter, no surprise line items. A gate realignment or latch replacement typically runs $180 to $420. Hinge replacement runs $180 to $400. A control board replacement on most operators runs $280 to $650 in parts. Full post replacement with a new concrete footing and Seminole County permit runs $600 to $1,200. What moves the price is access, gate weight, and whether reinforcement is needed before any operator work. Call (626) 649-4572 for a free estimate, and you will get the exact number in writing before we start.
We Also Serve Cities Near Fern Park
Our Fern Park customers are close to several larger metros, and we take calls across the region. We handle Gate Repair work in Jacksonville, Miami, Tampa, and Orlando as well. If you live outside Fern Park but need the same written-price, shoe-covers, cleanup-photo standard, Fern Park is where our local crews are scheduled from, and we would be glad to help you too.
Serving Fern Park, FL - Our Local Coverage Area
We’re based in the Fern Park area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Fern Park
Fern Park sits in a flat, low-lying stretch along US-17-92, and the June through September storms deliver lightning strikes that travel through unprotected gate circuits and destroy control boards. Most older slide-gate operators in the manufactured-home and retirement communities here have no surge suppression. A retrofit usually costs $120 to $240 and prevents the repeat board failure that keeps happening every wet season. Call (626) 649-4572 and we will check whether your operator already has protection.
Yes. Fern Park has no city government, so every structural gate repair, post footing, and electrical operator circuit must be permitted through the Seminole County building department. We pull that permit for you as part of the job. Contractors who work only in Casselberry or Altamonte Springs regularly skip this step, and the unpermitted repair then fails at resale inspection.
No, and we will not. A cracked or undersized post cannot carry a modern operator’s torque, and bolting a motor to it just transfers stress and cracks it further. The correct sequence in Fern Park, where the soil is soft and the water table is high, is to reinforce or replace the post footing first, then mount the operator. We will show you the crack, explain the load, and quote the reinforcement before any motor is ordered.
Yes. Many Fern Park acreage entrances and manufactured-home park perimeters sit too far from a power source for a conventional AC operator. We install solar-powered operators on Viking, Ghost Controls, and Mighty Mule hardware, sized to the gate’s weight and daily cycles. The panel, battery, and operator are quoted together as one written price, and we can also add a surge-protected controller on properties near the US-17-92 corridor.
We are factory-trained on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. In Fern Park specifically, most slide-gate communities run Viking or DoorKing, while private residential gates lean Ghost Controls or LiftMaster. We carry common parts for all of them, and we will tell you before ordering if a specialty part has to come from the manufacturer. Call (626) 649-4572 for a free estimate.
If your gate is stuck, sagging, or dead after a storm, call (626) 649-4572. A live person answers around the clock, and we will schedule your Fern Park repair with a written price before any work starts.
Written by Cody Beckman, Owner at Latch & Post Gate Repair, serving Fern Park since 2009.