Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Richland Hills
A new gate in Richland Hills rarely means starting fresh. Most of the homes here were built between 1950 and 1975, and the gate posts in the ground are just as old. What looks like a simple panel replacement is usually a job that starts with the post, the footing, and the frame before the gate ever gets hung. Our team works in Richland Hills regularly, and we understand what Blackland Prairie clay does to a fence line over thirty or forty years. For a written quote before any work starts, call us at (626) 649-4572.
Why Latch & Post Gate Repair Is Richland Hills’s Preferred Gate Installation Company
We’re the Gate Installation team that treats your backyard like it’s our own. Richland Hills homeowners call us because we show up on time, lay drop cloths before we step inside, and put on shoe covers at the door. Your floors stay clean, and there’s no chemical smell left behind. Cody Beckman leads our crews, and the standard he set is simple: written price before any work, quiet tools when kids are asleep, and a photo of the clean-up before we leave.
Every Richland Hills job carries the 365-Day Done Right Promise. If the gate isn’t right, we make it right. No argument, no fine print. Our technicians are background-checked, uniformed, and factory-trained on the brands families around here actually own. A live person answers the phone 24 hours a day, seven days a week. No voicemail, no callback queue. You call, a person picks up.
Driveway Gate Installation in Richland Hills
Driveway Gate Installation in Richland Hills usually means replacing a gate that was hung when the house was built, on a post that has shifted with every wet winter and dry summer since. The gate panel itself might be rusted through at the hinges or sagging so badly it drags the ground, but the real problem is almost always underneath: the post has been torqued out of plumb by shrink-swell clay, and the old footing was never intended to hold modern gate hardware. We pull the old post, recast the footing with a concrete collar, and hang the new gate on a post that stays put. A standard driveway gate installation here runs $1,400 to $3,200, depending on gate width, material, and whether the post needs a full reset.
Wood and steel driveway gates for older homes
Most Richland Hills driveways are narrow, and the original gate was likely chain-link or an old wood frame. A new steel frame gate with wood infill is a common choice because it matches the ranch-style look of the neighborhood and doesn’t fight the clay the way a solid panel does. We measure the opening, check the hinge post with a level, and quote the job in writing before anything gets ordered.
Operator retrofits and new openers
If the old operator still works but fails modern safety checks, we’ll tell you straight. Some legacy boards can’t be retrofitted to current entrapment-protection behavior. When that’s the case, replacing the operator alongside the gate makes more sense than bolting a new panel to a control board that’s past its useful life. We service Viking, Ghost Controls, and DoorKing systems and stock common replacement parts in the metro area.
Sliding Gate Installation in Richland Hills
Sliding Gate Installation in Richland Hills makes sense for lots where the driveway runs close to the house and there’s no room for a swing gate to arc open. Many older Richland Hills ranch homes have short, angled driveways, so a sliding gate that tracks along the fence line is often the only clean option. We install cantilever and track-style sliding gates, set the concrete track bed, and square the frame so the gate rolls true even as the clay underneath contracts and expands. Sliding gate installation here typically runs $2,800 to $5,500, with the track, wheels, frame, and operator included after a site measure.
Track beds on clay soil
The track is where Richland Hills sliding gates fail first. A track poured directly on Blackland Prairie clay will heave and buckle within two seasons. We dig the bed, compact a base, and pour the concrete in a way that isolates the track from the worst of the movement. It’s not glamorous, but it’s the difference between a gate that rolls for a decade and one that jams every spring.
Operators for sliding configurations
A sliding gate needs an operator matched to the gate’s weight and the length of travel. We size the motor correctly, set the limit switches, and mount the safety photocell at the right height. We also configure the auto-close and obstruction reversal so the gate never pushes against a kid or a dog standing in the path.
Trusted Brands We Service in Richland Hills
Our technicians are factory-trained on the equipment most Richland Hills homes actually run: Ghost Controls, Viking, and DoorKing, along with other major brands like LiftMaster, FAAC, BFT, Linear, Elite, and Mighty Mule. That training matters when a legacy control board has to be integrated with a new gate or a safety sensor from one brand needs to talk to a receiver from another. We keep common parts in the metro area, so most Richland Hills installs don’t wait on a long parts order.
Common Gate Installation Problems We See in Richland Hills Homes
- Posts torqued out of plumb by clay: The ground under Richland Hills swells in wet winters and shrinks in August. A gate post set in that soil decades ago will lean, and a gate hung on it will rack out of square. Skipping a concrete collar reset means the new gate binds within one or two wet-dry cycles.
- Legacy control boards that can’t be retrofitted: Many original operators around Richland Hills are models that no longer meet current entrapment-protection safety behavior. Retrofitting is sometimes possible, but often a full board and operator swap is cheaper than patching an obsolete system.
- Corroded original hinges and latches: The hardware on a gate from the 1960s or 1970s has been rusting for fifty years. A new gate panel hung on those old hinges puts modern weight on metal that was sized for a much lighter door. We replace hinges and latch posts as part of the install, not as an add-on.
- Straight-line wind stress on old frames: Spring thunderstorms in Tarrant County bring winds that hit a gate face hard. The original wood or thin-wall chain-link frames were never built for that load. We frame new gates with enough rigidity to hold square through those storms.
Pricing for Gate Installation in Richland Hills, TX
We quote every Richland Hills job in writing before any work starts. Here’s what to expect in this market. A pedestrian gate with new hardware and a post check runs $850 to $1,500. A standard driveway swing gate on a reset post runs $1,400 to $3,200. A sliding driveway gate with track bed and operator runs $2,800 to $5,500. A double driveway gate with two panels and a single operator runs $3,000 to $5,000. Security gates with reinforced framing and keypad entry run $2,200 to $4,900, plus access control hardware. You’ll see the exact number before we touch anything, and the price doesn’t change after we start.
If you’re looking at a full gate replacement on a home from the 1950s or 1970s, plan on the post work being part of the quote, not an extra. That’s the part we won’t skip, because it’s the part that determines whether the gate still swings true in three years. Call (626) 649-4572 and we’ll measure, check the posts, and hand you a written number.
Key Takeaways
- Most gate installations in Richland Hills are replacements on decades-old posts that need concrete collar resets before any new gate is hung.
- Written pricing is provided before work begins. Every time. No pressure.
- Shoe covers, drop cloths, and a cleanup photo are included. Floors stay clean.
- The 365-Day Done Right Promise covers every installation. If it’s not right, we make it right.
- A live person answers our phone 24/7. Call (626) 649-4572 and ask for Cody Beckman’s team.
We Also Serve Cities Near Richland Hills
Our crews serve Richland Hills and surrounding communities through the Dallas-Fort Worth metro area. Homeowners in Houston, San Antonio, Dallas, and Fort Worth reach us for the same written-price approach and 365-Day Done Right Promise. If you’re in one of those cities and need gate work, call the same number and ask about scheduling.
Serving Richland Hills, TX - Our Local Coverage Area
We’re based in the Richland Hills area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Installation in Richland Hills
Sometimes, but not if the post has been pushed out of plumb by the clay. We check the post with a level first. If it’s solid and straight, we can use it. If it has moved, hanging a new gate on it means the gate will sag within a year or two. The honest answer for most original posts from the 1950s to 1970s is a footing reset with a concrete collar. Call (626) 649-4572 and we’ll tell you what your post actually needs, in writing.
Because the panel was never the problem. In Richland Hills, the post underneath has been moved by decades of shrink-swell clay, and when the post leans, the gate follows. Fixing the panel without resetting the post is like straightening a picture on a wall that’s tilting. The post reset is the fix. It costs more than a panel patch, but it’s the only fix that lasts through the next two wet winters.
Not always. If the operator meets current safety standards and can accommodate the new gate’s weight, we can keep it. But many legacy boards around Richland Hills are from a generation before current entrapment-protection behavior was required. When that’s the case, keeping the old board means the new gate won’t meet safety behavior a family with kids and pets should expect. We’ll tell you honestly which situation you’re in, and you’ll see the options in writing before you decide.
Yes. Sliding gates are a common choice in Richland Hills where the driveway is short and a swing gate would arc across the yard. We install cantilever and track-style sliding gates, pour the concrete track bed properly so it doesn’t heave with the clay, and match the operator to the gate’s travel and weight. Sliding gate installation here runs $2,800 to $5,500 after a site measure, and you’ll have the exact number before we order anything.
More than swapping the panel. The typical Richland Hills job on a home of that age starts with checking the hinge and latch posts for plumb, which in most cases means pulling at least one post and recasting the footing with a concrete collar. Then we square the adjacent fence frame, replace hinges and latches sized for the new gate’s weight, and install the new panel and operator. If the old operator is obsolete, that gets replaced too. The whole job is quoted upfront, and the clean-up is part of it. Call (626) 649-4572 for a free estimate and a straight answer on what your gate needs.
Contact Latch & Post Gate Repair for Gate Installation in Richland Hills
If you live in Richland Hills and your gate is sagging, dragging, or just done, call us at (626) 649-4572. We’ll schedule a measure, check the posts, and hand you a written price before any work starts. A live person answers the phone day or night. Shoe covers go on before we walk in, drop cloths go down before we move a thing, and a photo of the clean-up is yours before we leave. That’s the Cedarwell Care Promise, and it’s on every single Richland Hills job.
Written by Cody Beckman, Owner at Latch & Post Gate Repair, serving Richland Hills through the Dallas-Fort Worth metro area since 2009.