Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Electric Gate Repair Across Yonkers
Electric gate repair in Yonkers means dealing with salt brine, steep streets, and 80-year-old masonry that shifts every winter. We replace corroded control boards, reset hinge posts knocked out of plumb by frost heave, and use stainless fixings that hold up near the tidal Hudson. Our Electric Gate Repair team serves homeowners across Yonkers, from Park Hill to the southwest riverfront, with a live person answering at (626) 649-4572 around the clock.
Most opener failures here trace back to two things: brine runoff shorting the board, or a post that moved over the thaw. You’ll get a written price before any work starts, shoe covers and drop cloths on every visit, and a cleanup photo before the technician leaves. That’s how Latch & Post Gate Repair works in Yonkers.
Key takeaways:
- Yonkers gates fail faster from salt brine on steep streets and tidal moisture near the Hudson.
- A typical gate opener board replacement runs $280-$520; full operator swaps start around $900.
- We reset shifted posts, replace corroded boards, and spec stainless hardware for coastal Yonkers blocks.
- Live person answers 24/7. Written price before work starts. 365-Day Done Right Promise on every job.
Why Latch & Post Gate Repair Is Yonkers’s Preferred Electric Gate Repair Company
We focus only on gates. Not garage doors, not general handyman work. Every gate comes down to two parts, the latch that holds it and the post that carries it, and that’s the job we focus on. That narrow focus matters in Yonkers, where a cast-iron gate hung on a brick pillar 90 years ago needs a different repair sequence than a steel tube gate on a modern post. Cody Beckman leads our gate repair work, and every technician is background-checked, uniformed, and factory-trained on the brands Yonkers families actually own: FAAC, BFT, and Viking among them.
We’ve been part of the Cedarwell family since 2009. The Cedarwell C.A.R.E. values govern every visit: Clean up like it is our own home, Ask before we move anything, Respect the family’s time and quiet hours, Explain the price before the work. We lay drop cloths on the floor and put on shoe covers before we step inside. When there’s a choice in lubricants, we use pet-safe options. If a kid is napping, we run quiet tools. You’ll see the exact dollar figure in writing before we touch anything, and you’ll get a photo of the cleanup before we leave.
Commercial Gate Operator in Yonkers
Commercial Gate Operator service in Yonkers typically involves a swing or slide gate driven by a 1/2 HP to 1 HP operator, a control board, safety edges or photo eyes, and a keypad or radio receiver. On multifamily properties near the Saw Mill River Parkway and along Yonkers Avenue, these systems run hundreds of cycles a day, and the boards take a beating from winter brine and Hudson River humidity. A corroded commercial board replacement usually runs $650-$1,200 in Yonkers; a full operator swap with arms and brackets starts around $1,500 and can reach $3,800 depending on gate weight and post condition.
Board Replacement and Harness Rework
When brine gets into a commercial operator enclosure, the failure usually starts at the terminal block. We replace the board, clean the harness, re-terminate with sealed connectors, and test every safety input before closing the enclosure. If the post has shifted, we address that too. A fresh board on a leaning post just fails again in the next thaw.
Hydraulic vs Mechanical Swing Operators
Older Yonkers multifamily buildings often have linear arm operators bolted to brick or bluestone pillars. When frost heave racks the pillar, the arm binds and the motor burns out. We shim the post, remount the operator on a new steel plate, and check sweep speed and force limits so the gate closes fully without slamming.
Gate Opener Repair in Yonkers
Gate Opener Repair in Yonkers comes down to three jobs: board replacement, limit and force adjustment, and post realignment. The steep blocks off Nepperhan Avenue and Riverdale Avenue send salt-laced runoff down the hill, and that brine follows the conduit into the operator housing. We see corroded FAAC and BFT control boards on waterfront properties five to seven years before the same model fails inland. A board swap typically runs $280-$520 in Yonkers. A full opener replacement, board, motor, arm or rack, starts at $900 and goes up from there.
Corrosion Repair on Operator Boards
We open the housing, document exactly what is corroded, and give you a written price before replacing anything. Often the motor is fine but the low-voltage side is gone. We replace the board with the correct model for your operator, not whatever is on the truck, and we spec stainless hardware on reassembly.
Post Reset After Frost Heave
Spring calls in Yonkers frequently start with a gate that drags and a latch that will not catch. The hinge post has moved. We reset the post footing, re-shim the hinges, and re-plumb the gate so it swings freely. This job usually runs $450-$800 including concrete, shims, and labor, and it is the fix that makes the opener work properly again.
Trusted Brands We Service in Yonkers
We are factory-trained on FAAC, BFT, and Viking operators, plus the residential brands Yonkers homeowners run every day: LiftMaster, Linear, Ghost Controls, DoorKing, Elite, and Mighty Mule. Because Yonkers is a 30-minute drive from our New York City office, we keep common boards, safety edges, and arms in local stock so the right part arrives on the first visit rather than a week later. That speed matters when a commercial gate is stuck open on a February night off McLean Avenue.
Common Electric Gate Repair Problems We See in Yonkers Homes
- Brine-corroded operator boards: Salt runoff from Yonkers’s steep streets follows conduit into the operator housing and eats the low-voltage side of the board. This shows up as intermittent opening, no response from remotes, or a gate that runs on its own.
- Frost-heaved hinge posts: On the hilly streets of Park Hill and the southwest riverfront, a heavy iron gate set on an old brick or bluestone pillar shifts several inches over one winter. The gate drags, or the latch misses the strike, even though the hardware is intact.
- Rusted galvanized hinges and brackets: The tidal Hudson keeps ambient moisture high on the western waterfront blocks. Galvanized fixings rust through years early, while painted steel peels and flakes. Stainless steel is the only material that holds up here.
- Stripped rack or worn limit switches: Slide gates on commercial properties along South Broadway run constant cycles, and when the rack wears, the gate shudders and trips the limit. We replace the rack section, re-time the limits, and re-seal the electronics.
Pricing for Electric Gate Repair in Yonkers, NY
A control board replacement in Yonkers runs $280-$520. A hinge post reset, which is the most common spring call here, runs $450-$800. A full gate opener replacement with new operator, arms, and safety edges starts at $900 for residential and $1,500 for commercial. What moves the price is the gate weight, whether the post needs resetting, and how much corrosion has spread through the harness. You’ll get a written quote before any work starts, and every price covers cleanup, shoe covers, and the 365-Day Done Right Promise. Call (626) 649-4572 for a free estimate.
We Also Serve Cities Near Yonkers
Besides our Yonkers work, we take electric gate repair calls from Mount Vernon, New Rochelle, White Plains, and the Bronx. The salt and frost problems shift block by block, and we know the difference between a waterfront Yonkers gate and a White Plains hilltop install. See our full Electric Gate Repair in Yonkers coverage or call to schedule.
Serving Yonkers, NY - Our Local Coverage Area
We’re based in the Yonkers area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in Yonkers
Yonkers’s steep, hilly streets send salt brine from winter road treatment downhill, and that runoff follows the conduit into the operator housing near the Hudson waterfront. The brine corrodes the control board’s low-voltage side years before the same model fails in flat, inland Westchester. Add tidal moisture from the Hudson and you get a corrosion rate our techs see in Yonkers five to seven years earlier than in White Plains. Call (626) 649-4572 and we’ll open the housing and show you exactly what failed.
Use stainless steel hinges, brackets, and fasteners, not galvanized. Seal every conduit penetration into the operator housing with marine-grade grommets or silicone. If your gate hangs on an old brick or bluestone pillar, have the post inspected each spring for movement, and reset it before the gate drags. We can quote preventive work in writing before any repair begins.
A heavy iron gate that suddenly drags or won’t latch, caused by a hinge post that shifted out of plumb when the ground thawed. The opener and latch are usually fine; the post has moved. We reset the footing, shim the hinges, and re-plumb the gate, typically for $450-$800. Call us and we’ll schedule the reset before the operator burns out fighting the bind.
Most board, opener, and hardware repairs do not need a permit. If the hinge post needs a new footing, or the pillar is cracked and requires structural work, Yonkers Building Department rules apply, and we coordinate that. We know the difference between a Bronx-style post job and a Yonkers one, and we will tell you upfront if a permit is required.
Every automatic gate should have photo eyes or a safety edge, plus force settings that reverse the gate if it meets resistance, and a manual release for power outages. Yonkers’s older multifamily properties often have original wiring without current safety devices, and we bring those systems up to code while we are repairing the operator. We explain what we add and why, and the price is in writing first.
If your gate is dragging, shorting, or stuck, call (626) 649-4572 now. A live person answers, day or night, and we will set a time that works for your family. The estimate is free, the price is written before work starts, and the repair is covered by the 365-Day Done Right Promise.
Written by Cody Beckman, Owner at Latch & Post Gate Repair, serving Yonkers and nearby Westchester communities since 2009.