Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Electric Gate Repair Across Newark
Electric gate repair in Newark usually means working on hardware that’s older than most of the homes around it. We’re talking about original wrought-iron gates hung before 1940, often in the Ironbound or the North Ward, where salt air from Newark Bay has been eating at the hinges for decades. Latch & Post Gate Repair is a Cedarwell-family gate specialist, and we know what those gates need. If your gate won’t open, grinds when it moves, or sags so badly it drags on the bricks, call us at (626) 649-4572. We’ll send a background-checked, uniformed technician who answers your questions plainly and writes the price down before any work begins.
Why Latch & Post Gate Repair Is Newark’s Preferred Electric Gate Repair Company
We focus on gates. Not fences, not general handyman work. Every gate comes down to two parts: the latch that holds it and the post that carries it. That’s the job we focus on, and in Newark that focus matters because the gates here are different. Cody Beckman, who runs Latch & Post, has built the service around a simple idea: name the price before the work, protect the home while we’re in it, and stand behind the result for a full year.
Our Newark customers tend to live in rowhouses and two-family homes where the driveway gate is inches from the front door. That means our techs work quietly, lay drop cloths on the floor, and put on shoe covers before stepping inside to reach an interior keypad or control box. We choose pet-safe lubricants where there’s a choice, and we can schedule around nap time if quiet matters. We operate under the Cedarwell C.A.R.E. values: Clean up like it’s our own home, Ask before we move or touch anything, Respect the family’s time and quiet hours, Explain the price before the work.
Every call is answered by a live person, 24 hours a day, 7 days a week. Nights, weekends, and holidays included. No voicemail, no callback queue. And every repair and installation is covered by the 365-Day Done Right Promise: if it isn’t right, we make it right. No argument, no fine print.
Electric Gate Motor in Newark
An electric gate motor in Newark carries a heavier load than the same motor in a suburban town, because so many of the gates it drives are century-old wrought iron with far more mass than a modern aluminum or steel panel. When a motor burns out, grinds, or stops responding in a Newark rowhouse, the fix usually involves more than swapping the unit. We check the gate’s swing geometry first. If the hinge post has moved over decades, a brand-new motor will fail the same way the old one did, just slower.
Expect a typical motor replacement in Newark to run between $650 and $1,400 depending on gate weight, operator type, and access. A basic residential swing-arm motor on a single pedestrian gate falls at the lower end. A heavy double-leaf driveway gate in the North Ward that needs a new gearbox and limit-switch calibration lands higher. You’ll see the exact number in writing before we touch anything.
Motor Replacement and Retrofit
The big Newark-specific decision is whether to repair an obsolete motor or retrofit a modern operator. Pre-2000 FAAC and BFT units often can’t accept modern safety photocells, and running one without proper entrapment protection violates UL 325. We’re factory-trained on FAAC, BFT, Linear, Viking, and LiftMaster, so we can tell you honestly when a retrofit makes sense and when replacement is the cheaper answer over two or three years.
Won’t Open or Stops Mid-Cycle
When a Newark gate stops halfway through its travel, the cause is often salt corrosion inside the limit switch or a failing capacitor on the control board. We diagnose on site, show you what we found, and quote the repair before we start. Most of these jobs finish the same day because we carry parts for the brands families actually own in Newark.
Gate Access Control in Newark
Gate access control in Newark covers keypads, remotes, intercoms, and the underground loops or photocells that tell the gate when to stop and reverse. On older Ironbound properties, the original gate was never designed for any of this. That means retrofitting a LiftMaster or FAAC operator onto a 1920s iron gate means first correcting hinge-post geometry and checking that the gate swings level. You can’t just bolt a motor onto a sagging frame and expect it to hold up.
Typical gate access control work in Newark ranges from $180 for a keypad repair or replacement up to $900 to $1,600 for a full retrofit with safety photocells, a new control board, and entry keypad. Remote control programming and replacement runs $75 to $150. Our tech carries remotes and keypads for FAAC, BFT, and Linear on the truck, so most access-control calls in Newark wrap up in one visit.
Keypads and Remote Programming
We replace keypads with units rated for outdoor exposure near salt air, which matters more in Newark than inland. We program remotes on site. If you’ve lost the master code, we can factory-reset most operators without replacing the board.
Safety Sensors and Photocells
Every automatic gate in Newark must have functioning entrapment protection. We install and align safety photocells, replace broken edge sensors, and test the reverse function before we leave. No modern operator should be running without these, and we won’t leave a gate in service that can’t stop for a child or a pet.
Trusted Brands We Service in Newark
We’re factory-trained on the brands Newark homeowners actually have: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We stock common parts locally for Newark jobs, which means less waiting on shipping and more one-visit repairs. If your FAAC control board is dead or your Linear actuator is grinding, we’ve handled it before and we’ll handle yours. We service the equipment we know, and we don’t pretend otherwise.
Common Electric Gate Repair Problems We See in Newark Homes
- Salt-air corrosion on original hinges and latch bolts. Newark Bay and Port Newark put salt in the air year-round, and it settles into every piece of exposed iron hardware. Hinges seize, latch bolts snap, and gates stop closing cleanly. We replace corroded hardware with galvanized or stainless components where the design allows.
- Post lean from freeze-thaw cycles. Newark’s shallow, brick-lined post footings heave every winter when water freezes and expands in the soil. An inward-swing gate that cleared the sidewalk in October may drag by February. We reset or replace posts and correct the swing geometry rather than just lifting the gate and calling it done.
- Obsolete control boards on legacy operators. Many Ironbound and North Ward gates still run pre-2000 FAAC or BFT boards that can’t integrate modern safety photocells. When those boards fail, repair isn’t always the right call. We’ll tell you when a new board and photocells cost less long-term than patching a 25-year-old unit.
- Outward-swing gates over the public sidewalk. In the Ironbound and parts of the North Ward, lots have zero or near-zero front setbacks. A gate that swings outward over the sidewalk can draw a Newark code violation. Our techs default to inward-swing or sliding track designs on these jobs because the sidewalk clearance simply isn’t there.
Pricing for Electric Gate Repair in Newark, NJ
Most electric gate repairs in Newark fall between $180 and $1,600. A keypad replacement for a FAAC operator runs about $180 to $250. A safety photocell repair or replacement is typically $225 to $400. Motor replacement on a single swing gate starts around $650 and climbs with gate weight and access. Hinge post replacement on an original Ironbound gate, including correction for sag and alignment, runs $700 to $1,400 depending on footing depth and brick condition. We quote the full price in writing before any work starts, and that number doesn’t change unless you ask us to add something. Free estimates, straightforward numbers, no pressure.
We Also Serve Cities Near Newark
Our Electric Gate Repair team serves Newark and the surrounding cities, including Elizabeth, Bayonne, Jersey City, and Hoboken. If you’re just over the city line, call and ask. Dispatch and scheduling for the area are coordinated from our New York City office, and crews serve Newark locally with the same written-price, shoe-covers, cleanup-photo routine we use everywhere.
Serving Newark, NJ - Our Local Coverage Area
We’re based in the Newark area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in Newark
Yes, in most cases you can keep the original gate leaf and replace only the failed hinge post. We remove the old post, core or repair the footing, and set a new galvanized steel core post. We then correct the gate’s swing geometry and rehang it. The gate stays. The rusted post goes. Expect this to run $700 to $1,400 in the Ironbound, where brick-lined footings are common. Call (626) 649-4572 and we’ll give you a written price.
Usually, yes, but first we correct the hinge-post geometry. A 1920s gate was never hung with a motor in mind, and if the post is even slightly out of level, the motor will fight it every cycle. We rehang and align the gate, then install a LiftMaster or FAAC operator sized for the gate’s actual weight. The retrofit includes safety photocells and keypad entry. That job typically runs $1,200 to $2,400 on an original iron gate, before the post work. Free estimate, always in writing.
Freeze-thaw cycles from December through March heave the shallow brick-lined post footings common in Newark’s oldest blocks. Water gets into the soil around the footing, freezes, expands, and pushes the post out of level. The gate sags and drags. We fix this by resetting or replacing the post and correcting the swing, not by shaving the gate bottom. Call (626) 649-4572 and we’ll take a look before the next freeze.
Newark automatic gates must have entrapment protection that meets UL 325, which means safety photocells or an edge sensor that reverses the gate when something is in the path. Older operators, especially pre-2000 FAAC and BFT units, often can’t support these sensors. We won’t leave an automatic gate running without functioning entrapment protection. If your gate can’t be brought into compliance, we’ll tell you what needs to change and quote it plainly.
If the rack is still straight and the pinion teeth aren’t stripped, a gear and bearing replacement usually fixes the grind for $300 to $500. If the rack itself is worn or the motor’s gearbox is full of salt corrosion, replacement is often cheaper over the next two years. We’ll show you the wear and quote both options so you can decide with the numbers in front of you. Estimates are free, and the price is written before any work starts.
Call Latch & Post Gate Repair for Electric Gate Repair in Newark
If your gate won’t open, grinds, sags, or won’t stop when it should, call us at (626) 649-4572. We’ll answer live, ask what’s happening, and set a time that works for you. The written price comes before the work. The drop cloths and shoe covers come standard. The cleanup photo comes before we leave. And the repair is covered by the 365-Day Done Right Promise, with Cody Beckman and the Latch & Post team standing behind it.
Written by Cody Beckman, Owner at Latch & Post Gate Repair, serving Newark and the surrounding New Jersey communities.