Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Electric Gate Repair Across Antelope
Electric gate repair in Antelope typically runs $180-$780 depending on whether it’s a control board, motor, safety sensor, or full operator replacement, and in most cases we can diagnose the problem on the first visit. Antelope’s concentration of late-1980s and 1990s tract homes means we work on a lot of legacy LiftMaster and Linear operators that are now hitting the 25-35 year failure window. If your gate is grinding, stuck, or refusing to close, call (626) 649-4572 and a live person will answer, day or night.
Why Latch & Post Gate Repair Is Antelope’s Preferred Electric Gate Repair Company
Our Electric Gate Repair team works Antelope daily, and we know the subdivisions here well enough to predict what a gate problem usually is before we arrive. Homes along Antelope Road and Don Julio Boulevard were mostly built between 1988 and 1998, and the operators installed then share the same wear patterns now. When a Linear board cooks in a 105°F July week, we see the same revision on three neighboring lots.
Cody Beckman, who leads our crews, has spent years on Antelope shared driveways and HOA entry points. We treat your floors and your time the way we’d treat our own. Shoe covers on before we step inside, drop cloths under any work at the motor housing, and a photo of the cleanup before we leave. The written price comes first, every visit, before anything gets unbolted.
Electric Gate Motor in Antelope
Electric Gate Motor repair in Antelope usually means either rebuilding or replacing the operator that drives the gate leaf. On the tract-home swing and slide gates here, the motor is often the original unit from the 1990s, and its output has degraded to the point where the gate stalls mid-cycle or trips the safety circuit. A typical motor repair in Antelope runs $220-$520; a full operator replacement is usually $480-$780.
Signs the Motor Is Failing
You’ll hear it before you see it. A healthy gate motor hums for a moment and moves the leaf. A dying one grinds, labors, and pauses. In Antelope specifically, we hear the same thing at HOA entrances off Don Julio and Antelope Road: a motor that was fine all winter starts dragging in June because the grease baked out of the bearings.
Repair vs. Replace
If the motor windings are intact and the issue is a worn gear or capacitor, we repair on the spot and you’ll see the number in writing first. If the motor is original to a 1992 build and replacement parts are discontinued, we’ll quote a modern operator that fits the existing post and rack, usually same visit.
Gate Access Control in Antelope
Gate Access Control covers the keypads, remote receivers, loop detectors, and intercom or phone-entry modules that tell the gate when to open. In Antelope’s HOA-heavy subdivisions, access control failures are as common as mechanical ones, and they strand residents at the same shared driveway entrances that were built when a single keypad served forty homes. Access control repairs in Antelope generally run $140-$430 depending on the component.
Keypads and Remotes
A dead keypad at a Don Julio Boulevard HOA entry usually traces back to a corroded harness or a failed receiver board, not the keypad itself. We test the full chain before quoting so you don’t pay for a part that wasn’t the problem. Remote programming on legacy FAAC or BFT receivers is something we handle regularly here.
Loop Detectors and Safety Sensors
Loop detectors buried in Antelope driveways fail silently. You notice it when the gate won’t close after a car exits, or starts closing on a car that’s still crossing. We’ll run a quick resistance test, pinpoint whether it’s the loop or the detector board, and give you a written price before any digging or board work begins.
Trusted Brands We Service in Antelope
We’re factory-trained on the operators Antelope actually has: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. A lot of Antelope’s late-80s and 90s HOAs installed Linear and LiftMaster slide operators, so we stock the common boards, gears, and safety edge parts locally rather than making you wait on a drop shipment. If you have an FAAC swing operator or a BFT control panel, we service those the same day too.
Common Electric Gate Repair Problems We See in Antelope Homes
- Cooked control boards from dry-heat summers. Antelope regularly sits above 100°F in July and August, and circuit boards inside steel operator housings don’t shed that heat well. When a Linear or LiftMaster board overheats, capacitors swell and the gate stops responding mid-cycle.
- Rust from tule fog after UV-damaged powder coat. The summer sun fades and cracks the factory finish on gate frames, then winter fog rolls in and the exposed steel rusts. Hinges seize, safety edges corrode, and wiring terminals loosen.
- Settled posts on 1988-1998 footings. The original post footings on many Antelope tract-home gates were poured to older standards and are now shifting. A gate that drags on the track or won’t latch is often the post, not the panel.
- Tight shared driveways forcing creative fixes. When two homes share one narrow driveway off a Don Julio side street, there’s no room to swing a gate leaf the other direction. We repair slide gates in place and keep one lane open for residents while we work.
Pricing for Electric Gate Repair in Antelope, CA
Here’s what Antelope homeowners and boards typically pay: gate motor repair $220-$520, control board replacement $180-$390, keypad or receiver repair $140-$280, safety sensor or loop detector repair $160-$320, full operator replacement $480-$780. The exact price depends on parts availability and access, but you’ll always see it in writing before we start. No dispatch fee to assess the job in Antelope, and the quote is yours to keep whether you approve the work or not.
We Also Serve Cities Near Antelope
We work throughout Antelope and the surrounding Sacramento Valley communities, including North Highlands, Elverta, Rio Linda, and Citrus Heights. If you’re on the border near Watt Avenue or Walerga Road, call (626) 649-4572 and we’ll confirm same-day or next-day coverage for your address.
Serving Antelope, CA - Our Local Coverage Area
We’re based in the Antelope area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in Antelope
Because they were installed at the same time. Antelope’s subdivisions along Antelope Road and Don Julio Boulevard were built in a tight window from the late 1980s through the mid-1990s, and the developers used the same operators community-wide. A Linear slide operator or control board that fails at one entrance is usually present at every other entrance in that subdivision, all at the same 25-35 year wear threshold. That’s why one repair call often turns into a quote for the full set. Call (626) 649-4572 and we’ll assess yours.
Yes, in most cases. We stock the common LiftMaster slide operator boards, gears, and safety edges that Antelope HOAs need, and for discontinued revisions we maintain relationships with suppliers who still carry them. If a part is genuinely gone from the supply chain, we’ll quote a modern equivalent that bolts to the existing post. The price comes in writing first.
Yes. We worked a shared-driveway HOA entry off Don Julio Boulevard where a legacy LiftMaster slide gate was dragging and tripping its loop detector every few cycles. The hinge post footing had settled and the rack and pinion was misaligned from years of 100°F+ thermal cycling. We corrected the sag, re-racked the operator, and swapped the failing control board while keeping one lane open for residents the whole day. Two other gates on that street had the identical operator and board revision, so the board asked us to quote the full set.
In Antelope, more often the post. Homes built between 1988 and 1998 frequently have undersized post footings by today’s standards, and dry clay soil shifts with the seasons. We’ll check post plumb and footing depth before assuming the gate leaf is the problem. If the post has settled, we correct the sag at the base; if the panel itself has warped from heat cycling, we’ll quote a replacement leaf.
Yes. Every automatic gate in Antelope, whether at a single-family home or an HOA entry, is required to have functional entrapment protection: photoelectric sensors or contact edges that stop and reverse the gate if something is in the path. Older operators sometimes have disconnected or bypassed safety circuits. We check them on every repair and quote the fix in writing before work begins.
Call Latch & Post for Electric Gate Repair in Antelope
If your gate is stuck, grinding, or refusing to open, call (626) 649-4572 now. A live person answers around the clock and we’ll schedule a technician for Antelope fast. You’ll get a written price before any work starts, shoe covers and drop cloths on every visit, and the 365-Day Done Right Promise behind the repair.
Written by Cody Beckman, Owner at Latch & Post Gate Repair, part of the Cedarwell family serving Antelope since 2009.