Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Temple City, CA
Temple City gate work has its own rhythm. The homes here, mostly 1940s to 1960s single-family ranches on 10 to 12 foot driveways, were never drawn for ornamental iron swing gates. Then the 2000s happened, and Temple City’s strong Chinese-American community commissioned hundreds of custom iron driveway gates from local fabricators. Those gates are now 10 to 20 years old, which means openers, hinges, and welds are wearing out on the same schedule. That’s the work we do at Latch & Post Gate Repair, and we do it with a written price before anything starts. Call (626) 649-4572 and you’ll reach a live person, day or night.
Why Temple City Homes Are Different
The San Gabriel Valley heat does real work on gates. Summer days above 100°F bake the powder coat on ornamental iron and dry out operator seals until they crack. Then the Santa Anas arrive in fall, carrying grit that settles into hinge barrels and accelerates rust. Gates that looked fine in March are binding or groaning by August. We see this pattern repeat across Temple City, from the ranch lots north of Las Tunas Drive down through the neighborhoods around Live Oak Park.
The bigger issue is the retrofit geometry. Most Temple City driveways were poured 60 years before anyone imagined a gate there. When a swing gate lands on a 10 foot driveway, the posts sit close to the property line, the hinges carry unusual side load, and the operator strains against a gate arm that was fabricated on site rather than engineered. Undersized steel, non-standardized hinge spacing, and motor mounts bolted to thin post caps are the norm, not the exception. A technician who only knows standard residential gates will misdiagnose half of what happens here. Cody Beckman trained our crews to look at Temple City gates as Temple City gates, not textbook examples.
We also know the question of movement. Nine out of ten service calls involve a gate that no longer travels true, either dragging on the driveway, sagging at the latch, or binding on the open side. In Temple City specifically, that usually traces back to the post, not the hinge. We check the post first.
Our Main Temple City Services
Temple City homeowners call us for three things, mostly: keeping an aging gate moving, replacing a gate that’s reached the end of its useful life, and solving electrical problems with automatic openers.
Gate Repair in Temple City
A gate that scrapes the driveway or refuses to latch is more common here than almost anywhere, because so many Temple City gates sit on driveways they were never sized for. We’ll inspect the posts, hinges, latch placement, and the weld points where local fabricators joined the frame. We stock replacement hardware for Viking, Ghost Controls, DoorKing, and Elite openers, which covers most of what’s installed in Temple City. If the post has shifted in its footer, we say so plainly and quote the fix. The full rundown is on our Gate Repair in Temple City page.
Gate Installation in Temple City
New gate work in Temple City almost always starts with the driveway width. A 10 or 12 foot opening changes what kind of gate makes sense, whether a two-leaf swing arrangement or a slide gate with a cantilevered track. We measure first, then quote. The written estimate includes the gate, the hardware, the operator if you want one, and the labor, and the price does not move after you approve it. We also flag clearance issues up front, because undersized setbacks are the single biggest reason new Temple City gates scrape within a year. Details are on our Gate Installation in Temple City page.
Electric Gate Repair in Temple City
Openers on Temple City gates fail for predictable reasons: heat-cracked seals, Santa Ana grit in the drive gears, and motors that have been fighting the same misaligned gate for years. We service Viking, Ghost Controls, DoorKing, and Elite operators, and we keep the common boards, remotes, and limit switches for these brands close at hand so most electric repairs are done in a single visit. We test the safety edges and photocells as part of every call, and we won’t leave an opener running until it stops cleanly in both directions. See our Electric Gate Repair in Temple City page for specifics.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Temple City
Most electric gates in Temple City run on four operator brands: Viking, Ghost Controls, DoorKing, and Elite. We work on all of them, and our techs carry the common replacement parts so a second visit isn’t needed. That covers 80% of what we see. For the full brand list and what to know about each one, visit our brands page.
Pricing for Gate Company in Temple City, CA
These are the ranges we quote most often in Temple City. Every price is confirmed in writing before work begins, so there is no surprise on the invoice.
| Service | Typical range in Temple City |
|---|---|
| Gate latch replacement | $120 - $240 |
| Hinge repair or replacement | $180 - $380 |
| Gate wheel or roller replacement | $140 - $260 |
| Weld repair on ornamental iron | $160 - $350 |
| Post realignment or re-setting | $300 - $700 |
| Electric opener repair (board, limit, or gear) | $220 - $480 |
| Remote programming or replacement | $90 - $180 |
| Safety edge or photocell replacement | $130 - $280 |
| Full gate installation | $2,400 - $7,500 |
| Electric opener installation | $900 - $2,800 |
In Temple City, two things push cost upward more often than the parts themselves: custom fabrication when a 2000s-era gate used non-standard hinge or post dimensions, and post work when the original footer was undersized for the gate it now carries. We quote those realities before the job, never after. The written estimate is free and it is the number you pay.
Neighborhoods We Serve in Temple City
We cover the whole city, and most calls fall within the same service area, so response is typically same-day or next-day depending on the time of the call.
- North Temple City, along and above Las Tunas Drive
- The neighborhoods around Live Oak Park
- East Temple City, near Cloverly Avenue and Temple City High School
- South Temple City, down toward the Longden Avenue corridor
- The Oak Avenue and Primrose Avenue residential blocks
Service Area – Cities Near Temple City
Our crews also cover the neighboring cities across the west San Gabriel Valley. If your gate is in one of these areas, we will come out with the same written-price promise and cleanup routine: El Monte, CA, San Gabriel, CA, Arcadia, CA, and Rosemead, CA.
Serving Temple City, CA - Our Local Coverage Area
We’re based in the Temple City area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Temple City
Most Temple City calls are scheduled same-day or next-day, and we route jobs by neighborhood so we’re not driving across town between stops. For a gate that won’t close or an opener that’s sparking, call (626) 649-4572 and a live person answers, night or weekend included.
Temple City requires a building permit for new driveway gates and for any post footing work that involves concrete. If you’re in an HOA, most Temple City HOAs also want a design review before installation, especially for ornamental iron. We can point you to the right office, but we never skip a required permit.
You’ll get a written list of what’s wrong, what’s urgent, and what can wait, with a price for each item. We wear shoe covers and lay down drop cloths if we need to enter the house, we test the gate in both directions, and we photograph the cleanup before we leave. The estimate costs nothing, and you decide what gets done.
If your Temple City gate is sagging, scraping, or refusing to open, call us at (626) 649-4572. We’ll give you a straight answer and a written price, before any work begins.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Temple City Customers Say
"Our gate opener quit and they came out quick. The tech was careful not to leave the yard open while our dog was out, which I really appreciated. Clean work, swept up the metal shavings."
- Eleanor Boggs"New hinges welded on a heavy gate. They laid down protection so no sparks hit the driveway and cleaned every bit after. Respectful of the property and the result is solid."
- Derek Pulanco"Electric gate was acting up. He was calm and methodical, found the bad sensor, and tidied the whole area by the gate post when he finished. No grease left on the driveway."
- Ravi Menon