Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Jacksonville
When a driveway gate stops opening in Jacksonville, the problem usually traces back to one of three things: a builder-grade operator that was never sized for the gate, a hinge post that’s softened from months of rain and salt air, or a flooded loop detector near San Marco or Ortega. We fix all three, and we do it the same way every time: shoe covers on, drop cloths down, a written price in your hand before we touch a single bolt. If your gate is stuck, sagging, or refusing to close, call (626) 649-4572 and a live person answers, day or night.
Jacksonville is over 900 square miles of consolidated city, the largest land area in the continental U.S. One crew here can be at an Intracoastal-front subdivision in the morning and an inland master-planned community off Bartram Park in the afternoon. The conditions are never the same twice: salt-air corrosion clocks along the St. Johns run 30 to 40 minutes away from dry, inland conditions on the same route. That’s why the person who shows up has to understand Jacksonville’s specific failure patterns, not just gate hardware in general.
Why Latch & Post Gate Repair Is Jacksonville’s Preferred Gate Repair Company
Since 2009, Latch & Post has worked as part of the Cedarwell family of independently owned and operated gate specialists. We’re not a general handyman service or a big-box dispatch center. We repair gates, we install gates, and we fix electric gates. That’s the whole job. And every visit runs on the Cedarwell Care Promise: a written price before work starts, shoe covers and drop cloths on every trip inside, and a photo of the clean-up before the technician leaves.
For families in Jacksonville, the part that matters most is what happens around the repair. We lay drop cloths on the floor and put on shoe covers before we step inside, so your floors stay clean. We choose pet-safe lubricants where there’s a choice, and we can schedule around nap time if quiet matters. Background-checked, uniformed technicians follow the C.A.R.E. values on every job: Clean up like it is our own home. Ask before we move or touch anything. Respect the family’s time and quiet hours. Explain the price before the work.
Cody Beckman leads the crew, and every job is backed by the 365-Day Done Right Promise. If the repair or installation isn’t right, Latch & Post makes it right. No argument, no fine print.
Driveway Gate Repair in Jacksonville
Driveway Gate Repair in Jacksonville usually comes down to a gate that has dropped on its hinges, a post that has shifted in soft ground, or an operator that was never strong enough for the gate it’s pulling. Most standard gate-latch replacements here run between $180 and $340. A sagging gate that needs hinge replacement and post reinforcement typically lands between $400 and $900 depending on the weight of the gate and whether the post needs to be reset in concrete. You’ll see the exact number in writing before we begin.
Builder-Grade Operator Replacement
Many Jacksonville homes in Bartram Park and the Southside were built during the 2000s and 2010s with a gate installed manual, or with a builder-grade operator that was never sized for the gate the homeowner later automated. We see operators that cycle out early because they have been dragging a gate three times heavier than they were rated for. We replace them with properly sized units from LiftMaster, Linear, or DoorKing, and we re-check the rack, pinion, and post footing at the same time.
Post and Hinge Stabilization
A soft hinge post is the most common reason a Jacksonville driveway gate sags. After 50-plus inches of rain a year, the footing under an older post can shift, and the gate starts scraping the driveway. We rebuild the post footing, swap in fresh hinges, and realign the gate so it swings without dragging. The price is quoted and agreed before any work starts, always.
Gate Welding in Jacksonville
Gate Welding in Jacksonville is the fix for ornamental iron that has split, cracked, or corroded through, especially along the Intracoastal and the Ortega and Mandarin riverfront corridors. Salt air eats iron and steel hardware in three to five years here, the same hardware that lasts a decade in Orlando. Small crack repairs and seam welding on a standard ornamental gate run $250 to $500. Full rust remediation with cut-out and replacement of corroded sections runs $600 to $1,400 depending on how much metal has to come out.
Weld and Rust Repair
We grind back the rust, cut out the corroded section, and weld in fresh steel or wrought iron that matches the gate’s profile. Then we prime and coat the repair so it can stand up to Jacksonville’s 90% plus summer humidity. If the corrosion has reached the hinge brackets, we replace those at the same time, because welding a gate back to a weakened bracket just moves the failure point.
Hinge and Post Reinforcement
Where a post has rusted out at the base or the hinge tabs have torn away, we can weld new hinge plates and reinforce the post with fresh steel before resetting it. This is the durable fix for older 1970s and 1980s Deerwood and Southside Estates gates that were built with ornamental iron and brick columns.
Trusted Brands We Service in Jacksonville
Our technicians are factory-trained on the brands Jacksonville families actually own, including Linear, Viking, Ghost Controls, and DoorKing. That matters because the right fix usually means matching the operator to the gate that is already in the ground, not swapping in whatever is on the truck. We stock common parts locally for Jacksonville customers, so a failed control board or a stripped gear doesn’t mean waiting a week on a shipment. If the brand on your gate is one we service, we can typically have it diagnosed and repaired in a single visit.
Common Gate Repair Problems We See in Jacksonville Homes
- Flooded underground loop detectors. In San Marco, Ortega, and low-lying parts of the Beaches, heavy rain submerges the loop detector and the gate stops sensing vehicles. It will close on a car or refuse to hold open. The fix is a reset or replacement, and on repeat offenders we recommend moving the control box up onto a pedestal to get wiring out of the standing water zone.
- Salt-air corrosion on hinges and ornamental iron. Along the St. Johns and the Intracoastal, hinges, ironwork, and control boards fail in three to five years. The air here does in a decade what inland Florida does in ten. Corrosion remediation and marine-grade component upgrades are the defining service need.
- Sagging gates on soft post footings. With around 52 inches of annual rain and 90% humidity through summer, older post footings shift and the gate starts dragging. The fix is rebuilding the footing and replacing the hinges, not just adjusting the gate and hoping.
- Builder-grade operators that were never sized right. Across Bartram Park and the Southside, we see aluminum slide and swing gates paired with operators that were installed for a manual gate and later automated. The operator cycles out early because it has been overworked from day one. We replace it with a correctly rated unit and verify the rack and pinion are aligned.
Pricing for Gate Repair in Jacksonville, FL
A standard gate-latch replacement in Jacksonville runs $180 to $340. Hinge replacement with post stabilization runs $400 to $900. Small weld and rust repairs run $250 to $500, and full corrosion remediation runs $600 to $1,400. Gate operator replacement, depending on brand and gate weight, typically lands between $600 and $1,800 including installation. These are honest, written numbers, and you get the exact price before any work starts. We do not bill a cent beyond the agreed quote. Call (626) 649-4572 for a free estimate and we’ll put the price in writing on your kitchen counter before we touch anything.
We Also Serve Cities Near Jacksonville
Our crew works throughout Jacksonville and the surrounding communities, including Orange Park, Fleming Island, Middleburg, and Atlantic Beach. If you’re just outside the city limits and your gate is down, call us. The same written price and the same crew that handles Gate Repair in Jacksonville are the ones who show up at your door.
Serving Jacksonville, FL - Our Local Coverage Area
We’re based in the Jacksonville area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Jacksonville
The actual fix is usually two parts: reset or replace the flooded underground loop detector, and elevate the control box off the ground so the wiring stops sitting in standing water. We see this constantly in San Marco, Ortega, and low-lying Beaches neighborhoods. After we get the gate sensing again, we can move the operator onto a pedestal mount, which rarely comes up in service manuals for Tampa or Orlando because those cities do not have the same flood-prone gate operators. Call (626) 649-4572 and we’ll send someone who knows where the water sits.
Salt air. Jacksonville has dual salt-air exposure, Atlantic beaches to the east and the St. Johns River and Intracoastal cutting through the city’s core. That air corrodes iron and steel gate hardware in three to five years, where the same hardware lasts a decade in inland Florida. The fix is corrosion remediation and marine-grade component upgrades, not just a fresh coat of paint. In Ortega and Mandarin especially, we replace hinges and fasteners with hardware built for the salt, and we coat everything before we leave.
Yes. We automate manual gates all the time in Deerwood, Southside Estates, and similar 1970s and 1980s subdivisions. The job requires running power and conduit, which often was not included during the original build, and then installing an operator sized for the gate’s weight and length. We also add UL 325 entrapment protection, including photo eyes and edge sensors, so the gate stops and reverses if a child or pet is in the path. The full installation including power run, operator, and safety edges typically runs $1,800 to $3,500 depending on the distance from the panel to the gate. You’ll get a written price before we start.
UL 325 is the safety standard that requires automatic gates to have entrapment protection: photo eyes, edge sensors, or both, plus a reversing mechanism. It means the gate cannot close on a person, a pet, or a car. You can check that it’s working by holding a cardboard box in the gate’s path while it closes. If the gate reverses, the protection is functioning. If it doesn’t, or if you hear grinding, call (626) 649-4572 and we’ll test, repair, or replace the safety system. This is required equipment, not an add-on, and it must work correctly on every automatic gate we touch.
Almost always just new hinges, and often a post footing rebuild. A sagging gate is a mechanical problem, not a gate problem. The hinge post has shifted, the hinges have worn, or the post has softened in the ground. We rebuild the footing, replace the hinges, and realign the gate. A full gate replacement is rarely needed unless the frame itself has corroded through. For most Jacksonville homes, sagging gate repair runs $400 to $900, and the gate is swinging clean by the time we leave.
Written by Cody Beckman, Owner at Latch & Post Gate Repair, part of the Cedarwell family of independently owned and operated gate specialists.
Call Latch & Post Gate Repair in Jacksonville, FL
When your gate is down, you want a straight answer and a clean house when the crew leaves. That’s the job. Call (626) 649-4572 and a live person answers, 24 hours a day, seven days a week. We’ll schedule a visit, hand you a written price before any work starts, and leave your floors as clean as we found them. The 365-Day Done Right Promise covers every repair and installation. If it isn’t right, we make it right. That’s it.