Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Fort Worth
Fort Worth Electric Gate Repair usually costs between $180 and $650, and most jobs are completed in a single visit. The price depends on what failed: a latch replacement sits at the low end, while a post reset in black gumbo clay runs higher because it requires digging out the old footing and pouring new concrete below the active shrink-swell zone. If your gate is sagging, dragging, or refusing to open, call us at (626) 649-4572 and we’ll give you a written price before any work starts.
Why Latch & Post Gate Repair Is Fort Worth’s Preferred Gate Repair Company
We’re part of the Cedarwell family, and we’ve worked on Gate Repair jobs across Fort Worth long enough to know what this soil does to a gate post. Fort Worth sits on expansive clay that moves with every rain and drought cycle, so a gate that was perfectly plumb in April can be dragging by August. Homeowners in Fairmount, the Near Southside, and the Alliance corridor call us because we don’t just tighten hinges and hope for the best. We check post depth, soil moisture, and the actual cause of the bind before we quote anything.
Every technician who arrives at your Fort Worth home is background-checked, uniformed, and trained on the gate operators families actually own, including FAAC, BFT, and Viking. We lay drop cloths on the floor and put on shoe covers before we step inside. If your kids are napping, we’ll use quiet tools and schedule around nap time when you ask. At the end of the visit, you get a photo of the clean-up before we leave. That routine is the Cedarwell C.A.R.E. standard, and it’s included on every job, not offered as an add-on.
Sliding Gate Repair in Fort Worth
Sliding gate repair in Fort Worth often comes down to two things: the track and the operator. On the ranch lots west of I-35W toward Benbrook, heavy pipe gates sit on steel track that flexes with the clay. In north Fort Worth’s newer subdivisions, lightweight aluminum slide gates warp in summer heat, and the rollers bind. Either way, the repair starts with a straight edge on the track and a check of the wheel bearings, because a gate that growls when it moves is usually fighting a misaligned track, not a dead motor.
Most slide gate track corrections in Fort Worth run between $220 and $480, including roller replacement when needed. If the operator itself has failed, a new FAAC or BFT slide operator typically lands between $750 and $1,300 installed, depending on the gate’s weight and length.
Track Realignment and Roller Work
Fort Worth’s freeze-thaw cycles are hard on slide gate hardware. Water seeps into roller assemblies during winter ice storms, freezes, and cracks the nylon wheels. Then summer arrives and the track has shifted from clay movement. We replace rollers, re-level the track, and make sure the gate travels without dragging before we call the job done.
Operator Replacement on Existing Slide Gates
When a builder-grade operator quits on a slide gate in the Alliance corridor, we usually find the operator was undersized from day one. We quote a properly rated replacement and adjust the limit travel so the motor isn’t stalling against a gate that’s moved out of square. The written price includes removal of the old unit and testing the full travel cycle three times.
Wrought Iron Gate Repair in Fort Worth
Wrought iron gate repair in Fort Worth is as much about the post as the iron. The ornate gates on 1920s and 1930s homes in Fairmount and the Near Southside have gorgeous original metalwork, but the posts underneath were set shallow, decades before anyone understood what black gumbo clay does. When a wrought iron gate starts dragging on the latch side, the post has usually tilted. We jack the gate back into position, then reset the post footing with concrete that extends below the active clay zone.
Typical wrought iron gate realignment in Fort Worth runs $260 to $540 when the post needs resetting. Weld repairs on cracked ornamental pickets or rusted-through bottom rails run $90 to $220 per repair point, depending on access and how much paint needs to be matched.
Rust and Weld Repair
Fort Worth’s humidity and irrigation overspray put wrought iron at constant risk of rust-through at the bottom rail. We cut out the rotted section, weld in matching steel, and grind the joint smooth. After the weld, we prime and paint to match the existing finish as closely as the age of the gate allows.
Post Resetting and Gate Hanging
If your iron gate has dragged for years, the answer is rarely just straightening the panel. On Fort Worth’s clay, the post is usually the problem. We dig out the old footing, check how deep it actually went, and pour a new base that clears the shrink-swell zone. Then we re-hang the gate and adjust the hinges so it swings freely without binding.
Trusted Brands We Service in Fort Worth
Our technicians are factory-trained on FAAC and BFT hydraulic operators, Linear swing and slide motors, and Viking residential gate operators, and we also provide Fort Worth Doorking service. We keep common control boards, photo-eyes, and limit switches stocked locally so a Fort Worth repair doesn’t stall waiting on a part from California. If your gate runs on a brand we don’t service, we’ll tell you honestly and point you to someone who can, rather than guessing at a board replacement.
Common Gate Repair Problems We See in Fort Worth Homes
- Builder-grade operators stalling on subdivisions. The 1990s through 2010s boom along the Alliance corridor and Keller border produced thousands of gates with undersized operators. When the clay heaves the post even an inch, the opener fights the bind and overheats.
- Manual ranch gates retrofitted with the wrong automation. West of I-35W toward Benbrook, plenty of pipe gates never had conduit trenched during the build. Homeowners add an opener later, fed by an extension cord or an undersized power run, and wonder why it fails in a year.
- Ice storm damage to slide gate rollers. North Texas ice penetrates automatic operator housings and freezes rollers solid. The first warm day after a freeze, the gate grinds and the rollers shatter.
- Shallow post footings on established ranch lots. Near Benbrook Lake, posts were routinely set without footings deep enough to clear the active clay zone. These gates rack out of plumb every wet-dry cycle until someone finally resets the post properly.
Pricing for Gate Repair in Fort Worth, TX
A latch replacement in Fort Worth typically runs $180 to $320. Gate realignment with post resetting lands between $260 and $540. Slide gate track correction with new rollers runs $220 to $480. A full operator replacement on a swing or slide gate starts around $750 and goes up based on gate weight and the brand you choose. Every price is written down and handed to you before we touch a single bolt. Estimates are free, and there’s no pressure to accept on the spot.
The two factors that move a Fort Worth quote the most are post condition and power access. If your post has heaved out of plumb, the job changes from a hinge adjustment to an excavation and concrete pour. If your gate has no power run, the quote includes trenching conduit to a safe, code-compliant power source. Both are priced before work begins.
We Also Serve Cities Near Fort Worth
Our gate repair service covers Fort Worth and the surrounding communities, including Haltom City, North Richland Hills, Hurst, and Kennedale. If you’re on the north side near the Keller border or south toward Benbrook, we’re familiar with the housing stock and the soil. Gate Repair in Fort Worth is our home base, but we schedule jobs across the whole area seven days a week.
Serving Fort Worth, TX - Our Local Coverage Area
We’re based in the Fort Worth area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Fort Worth
Usually not. In most Fort Worth subdivisions built from the 1990s through the 2010s, the stalling is caused by the gate leaf binding against a post that has heaved out of plumb in the clay. The opener is working hard against a gate that won’t swing freely, and it’s overheating or tripping its limit. We check the post alignment and the gate’s swing before we recommend replacing anything. Call (626) 649-4572 for a free assessment and a written price.
Yes, but the first thing we check is whether you have conduit and a proper power run to the gate. Many ranch properties out toward Benbrook never had electrical trenched during the build, and adding an operator means running power correctly, not stringing an extension cord. We quote the full job, including conduit, operator, and limit setup, before any work starts. A typical automation package starts around $900 and goes up based on gate length, gate weight, and the power distance from the house.
Fort Worth sits on open prairie with slightly colder exposure than Dallas, so ice storms here last longer and penetrate deeper into operator housings and roller assemblies. Water gets in, freezes, and cracks plastic rollers or seizes hydraulic seals. When the ice thaws, the gate still won’t travel smoothly. We replace rollers, re-lubricate tracks, and check the operator’s seals after every hard freeze. Call (626) 649-4572 if your gate is grinding after a storm.
No. On Fort Worth’s black gumbo clay, a sagging gate almost always means the hinge post has tilted or sunk. Straightening the panel without fixing the post just puts a bandage on the problem, and the gate will sag again within a year. We reset the post below the active clay zone and re-hang the gate so it swings true. That’s the repair that actually lasts.
Yes. Any automatic gate in Fort Worth that opens across a driveway or walking path needs working photo-eyes that stop and reverse the gate if a child, pet, or car breaks the beam. We test the photo-eyes on every repair visit and replace them if they’re not functioning. This is a safety item, not an upsell, and we’ll explain the cost before we replace anything.
Call Latch & Post Gate Repair at (626) 649-4572 for a free estimate on any gate repair in Fort Worth. You’ll get a written price before work starts, shoe covers and drop cloths on every visit, and a cleanup photo before we leave. And if something isn’t right within 365 days, we make it right, no argument.
Written by Cody Beckman, Owner at Latch & Post Gate Repair, serving Fort Worth as part of the Cedarwell family since 2009.