Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Corte Madera
Gate repair in Corte Madera typically runs between $180 and $2,800 depending on whether we’re replacing a latch, realigning a sagging panel, or installing a new operator on a hillside driveway. Most standard repairs are completed in one visit, and you’ll see the exact number in writing before we touch anything. We answer the phone live around the clock at (626) 649-4572.
Corte Madera splits into two very different gate worlds. East of Highway 101, the flat bayfront streets near the marshes have mid-century ranch homes where redwood gates and galvanized hardware fail from salt air. Above 101, the hillside properties have steep driveways, wide gates, and operators that work against grades most installers never account for. Cody Beckman and our crews know both sides of town because we’ve repaired hundreds of gates here, from the flats near Corte Madera Creek to the winding roads above Chapman Park.
Every visit includes shoe covers, drop cloths, and a cleanup photo before we leave. That’s not an upsell. It’s how the Cedarwell C.A.R.E. values work.
Key Takeaways
- Most gate repairs in Corte Madera cost $180-$2,800, with written pricing upfront.
- Salt-mist corrosion east of 101 demands stainless hinges and sealed operators, not standard galvanized parts.
- Hillside gates above 101 need operators sized for grade stress and pivot wear.
- We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule.
- Live person answers every call, 24/7, including holidays.
Why Latch & Post Gate Repair Is Corte Madera’s Preferred Gate Repair Company
We’re part of the Cedarwell family of independently owned gate specialists, operating since 2009 with a single focus: gates. Not fences, not general contracting. Every gate comes down to two parts, the latch that holds it and the post that carries it. That’s the job we focus on, and it’s why Corte Madera homeowners call us when their gate stops closing or their driveway operator gives up on a Sunday night.
Our reputation in Corte Madera is built on showing up when we say we will and leaving the house cleaner than we found it. Technicians wear uniforms, pass background checks, and follow a documented care routine: shoe covers at the door, drop cloths under the work area, quiet tools when kids are napping, and a photo of the cleanup before pulling out of the driveway. Families with dogs, toddlers, and white couches don’t have to hover over us.
We answer calls from Corte Madera with a live person, not a queue. When a gate fails at 10 p.m. and the dog can get out, you talk to a human who knows what a gate operator is. That matters more than any marketing language ever could.
Our Gate Repair team is factory-trained on the brands homeowners around here actually own. When a Viking operator near the marsh won’t respond, we don’t guess. We diagnose it the same visit, usually with parts on the truck.
Sliding Gate Repair in Corte Madera
Sliding gate repair in Corte Madera often comes down to two failures: the rollers and track on bayfront ranches where salt air eats bearings, and the motor sizing on hillside lots where the gate works against a grade. We see both constantly.
A standard sliding gate repair in Corte Madera runs $220-$650 for roller and track service, and $450-$1,400 when the operator itself needs a new control board or motor rebuild. You get the written number before we order a single part.
East of 101, we use sealed bearings and stainless rollers as the baseline. Anything galvanized will bind within two years. Above 101, we check whether the original installer oversized the operator enough for the slope. Most weren’t. That’s why a gate that worked for eight years suddenly won’t close without two nudges and a prayer.
Track and Roller Service
When a sliding gate drags or grinds, the track is usually filled with bay grit and the rollers have flat spots. We clean the track, replace the rollers, and realign the panel so it rides without strain on the motor. This is the single most common Corte Madera repair, especially on bayfront streets where salt grit accumulates fast.
Operator and Motor Repair
Sliding gate motors in Corte Madera’s hillside neighborhoods burn out faster than manufacturers expect because they’re pulling weight up a grade. We inspect gear teeth, limit switches, and controller boards before recommending a repair or replacement. If the motor is undersized, we’ll tell you the truth and quote the correct one.
Wrought Iron Gate Repair in Corte Madera
Wrought iron gate repair in Corte Madera is as much about corrosion management as it is about welding. The salt-mist off the tidal marshes east of 101 gets into every joint and hinge, and powder coat that would last twenty years in Larkspur fails in eight.
Typical wrought iron gate repairs here run $280-$900 for hinge replacements, rust treatment, and repainting. Full restoration of a heavily rusted gate, including weld repair and marine-grade powder coat, runs $900-$2,800. We quote the range upfront and you approve the exact number before work starts.
Every wrought iron gate we repair gets stainless or marine-grade hardware. We don’t use standard galvanized hinges on a bayfront gate, because we’d be back in two years and so would the rust.
Rust Treatment and Repainting
We grind out active rust, treat the surface, and repaint with a marine-grade finish that stands up to Corte Madera’s salt air. The prep work is the repair. Paint over untreated rust fails fast, and you’ll see it flaking again by spring.
Hinge and Weld Repair
Sagging wrought iron gates usually fail at the hinge post first. We weld cracked joints, replace worn hinge barrels, and reinforce the post footing if it’s shifted. On hillside properties above 101, we also check the post for lean before re-hanging the panel. A plumb gate closes cleanly; a leaning one fights the latch forever.
Trusted Brands We Service in Corte Madera
We’re factory-trained on the brands Corte Madera homeowners actually have on their property: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We stock local parts for common Viking and Ghost Controls failures because those two brands show up constantly in the hillside neighborhoods above 101 where solar and battery systems are common. When a DoorKing operator near the marsh needs a new limit switch, we usually have it on the truck. That means one visit, not two.
Common Gate Repair Problems We See in Corte Madera Homes
- Salt-mist corrosion on bayfront hinges and springs. East of 101, standard galvanized hinges oxidize and bind within two to three years. We spec stainless as the baseline, not an upgrade, for any property east of the highway.
- Sagging redwood gates on mid-century ranch homes. The 1950s and 1960s ranch neighborhoods near the shoreline still have original redwood gate frames. They rot at the hinge post and the latch post, and standard replacement hardware fails fast without marine-grade treatment.
- Grade-stressed operators on hillside driveways. Above 101, automated swing and slide gates sit on steep, winding driveways. The constant pull of gravity wears pivot bearings unevenly and burns out undersized motors years early.
- Solar and battery operator failures on wide gates. Hillside acreage entrances with long driveways often run solar-powered operators. When panels get shaded by redwoods or batteries reach end of life, the gate moves slow then stops entirely. We diagnose the full power system, not just the motor.
Pricing for Gate Repair in Corte Madera, CA
Here’s what we actually quote in Corte Madera. A latch replacement runs $180-$320. Track and roller service on a sliding gate runs $220-$650. A hinge and sag correction on a wood gate runs $280-$750. A full operator replacement, including labor and the correct motor for a hillside grade, runs $1,200-$2,800. Wrought iron rust repair and repainting falls between $280 and $900, with full restoration reaching $2,800.
What changes the number is the salt exposure east of 101 (stainless costs more than galvanized, but you won’t replace it in three years) and the gate’s size and grade above 101. Every quote is written, every line item explained, and nothing gets approved without your signature. Call (626) 649-4572 for a free estimate. We’ll tell you the honest number before you commit.
We Also Serve Cities Near Corte Madera
Our Corte Madera customers send us to family in Larkspur, Mill Valley, Kentfield, and San Rafael too. Same written pricing, same shoe covers, same live person on the phone. If you’re a few minutes outside town, we’re already working in your neighborhood.
Serving Corte Madera, CA - Our Local Coverage Area
We’re based in the Corte Madera area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Corte Madera
Salt-laden air from the Corte Madera tidal marshes and San Francisco Bay settles on metal surfaces east of Highway 101 and accelerates oxidation far faster than in inland Marin. Standard galvanized hinges and motor housings typically show binding and visible rust within two to three years. We use stainless hardware and NEMA-4-rated sealed operators on bayfront properties as the default spec. Call (626) 649-4572 for a free inspection of your gate’s corrosion level.
Yes, solar gate openers work well on Corte Madera hillside properties, but the panel must be sized for redwood shade and winter sun angles, and the battery bank must match the gate’s daily cycle count. Undersized solar setups cause slow operation and premature motor wear. We install and repair solar systems on wide farm gates and long driveways throughout the hills above 101.
The hinge post footing typically fails first, especially on hillside gates where gravity pulls the panel downhill year after year. The post leans, the gate sags, and the latch no longer aligns. In the flats near Corte Madera Creek, we’ve repaired a 1950s ranch’s original wood swing gate where the galvanized hinge post had rusted through at the base. We reset the post, installed stainless hinges, and sealed the operator housing against salt air.
Yes, every automated gate in Corte Madera should have functioning safety photocells and obstruction detection, and California law requires entrapment protection on automated gates. We add photocells to older installations and test them on every service call. If your gate doesn’t reverse when a child or dog crosses the beam, that’s a repair priority, not an optional add-on.
We remove the active rust, weld any cracked joints, and apply a marine-grade powder coat or paint system designed for salt-air exposure. The key is stainless hardware and proper surface prep. Standard paint over untreated rust fails within a year in Corte Madera’s bayfront air. Our approach costs more upfront and lasts far longer. Call (626) 649-4572 for an exact quote on your wrought iron gate.
Written by Cody Beckman, Owner at Latch & Post Gate Repair, serving Corte Madera since 2009.