Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Bedford
Gate repair in Bedford usually comes down to one of three things: a post that’s no longer plumb, hinges that have sagged under decades of use, or an operator that’s finally given up. Most Bedford homes were built between the 1970s and early 1990s, which means the original gates and openers are now 30 to 50 years old, and they show it. We know the neighborhoods, the soil, and the specific ways gates fail here. If your gate is dragging, leaning, or refusing to open, call us at (626) 649-4572 and we’ll send a technician who knows Bedford’s housing stock as well as you do.
Why Latch & Post Gate Repair Is Bedford’s Preferred Gate Repair Company
Gate Repair is all we do. Latch & Post is part of the Cedarwell family of independently owned and operated gate specialists, and we’ve been at this since 2009. That focus matters in Bedford, where the call is rarely simple. A homeowner schedules a hinge adjustment, and our technician finds the post hollow at the soil line. We expect that here. Our crews work from the brand’s Dallas-Fort Worth office, so Bedford customers get local response without the guesswork of a general handyman. Every technician is background-checked, uniformed, and factory-trained on the brands families actually own: Viking, Ghost Controls, DoorKing, and Elite among them. When you call, a live person answers. Not a queue, not a callback. And before any work starts, you’ll see a written price. No surprises, no pressure.
Iron Gate Repair in Bedford
Iron Gate Repair in Bedford is often about rust, welds, and post movement rather than the panel itself. Wrought-iron swing gates hung in the 1980s have decades of Tarrant County weather in them. Cracked welds from hard freezes, seized hinges from clay-driven post tilt, and rust bleed at the bottom rail are all common. In Bedford, a typical iron gate repair runs $180 to $520 depending on the weld work and whether a post needs resetting. We quote the exact number in writing before touching anything.
Weld and Rust Repair
When a February 2021-style freeze cracks a weld, the gate doesn’t fail all at once. It twists slightly, then binds. We grind out the cracked bead and re-weld, then treat the rust so the repair doesn’t rot out again in two seasons. On most Bedford iron gates, this is a half-day job.
Post Reset for Iron Gates
Black clay soil in Bedford doesn’t just tilt posts. It works them loose enough that the gate’s weight shifts entirely onto the hinges. We pull the post, dig a proper footing, and reset it plumb. The panel usually doesn’t need replacing once the post is true.
Sliding Gate Repair in Bedford
Sliding Gate Repair in Bedford frequently involves track alignment and roller wear on gates installed in the 1980s and 1990s. These slide gates run on steel track embedded in concrete that’s been heaved by the same shrink-swell clay that wrecks posts. When the track dips or the rollers flatten, the gate shudders, stalls, or jumps the rail. A typical sliding gate repair in Bedford runs $220 to $640, depending on whether we’re replacing rollers, realigning track, or addressing operator issues. You’ll get the exact figure in writing first.
Track and Roller Correction
Bedford’s clay doesn’t just move posts; it shifts the concrete pads slide tracks are bolted to. A gate that was smooth five years ago now hesitates mid-travel. We level the track, swap worn rollers for new sealed bearing units, and get the gate moving cleanly again.
Slide Gate Operator Problems
When a 1990s slide gate operator stops responding, the issue is often a burnt control board or a seized motor, not the gate itself. We’re factory-trained on Viking, Ghost Controls, and DoorKing, so we can often repair rather than replace. If the board is obsolete and won’t accept modern safety photocells, we’ll tell you straight: retrofit or replace, with numbers for both.
Trusted Brands We Service in Bedford
We service and repair the operator brands Bedford homeowners actually have on their gates, including Viking, Ghost Controls, DoorKing, and Elite. Because we’re focused exclusively on gate work, our Dallas-Fort Worth office keeps common parts on hand rather than ordering everything in, which means fewer return trips for Bedford customers. Whether it’s a Ghost Controls sliding operator from the 1990s or a newer Elite swing arm, our technicians show up knowing the equipment. We don’t learn on your gate.
Common Gate Repair Problems We See in Bedford Homes
- Hollow cedar hinge posts. In Bedford’s 1980s subdivisions, original cedar gate posts have been sitting in clay moisture cycles for 30 to 50 years. By the time the gate sags, the post is usually hollow at the soil line and needs a full pull-and-reset.
- Legacy control boards that reject modern safety devices. Many 1980s and 1990s operators were built before UL 325 entrapment protection became standard. When you try to add a keypad or safety photocell, the old board simply won’t accept it. We’ll show you the retrofit path and the replacement cost side by side.
- Freeze-cracked welds on wrought-iron gates. The February 2021 hard freeze snapped welds across Bedford. Some show up immediately; others fail months later when stress finally wins. We inspect for hairline cracks even when the visible problem is just a gate that suddenly sticks.
- Operators that reverse mid-travel. On a call in Bedford’s Oak Hollow neighborhood, a homeowner’s 1980s swing gate was dragging on the driveway and the LiftMaster operator would reverse mid-travel. Our tech found the hinge post hollow at grade and pulled and reset it on a new post footing. The panel was fine once the post was true. A quick sag correction and a safety photocell check later, the same operator ran the gate full-travel without reversing.
Pricing for Gate Repair in Bedford, TX
In Bedford, a hinge adjustment that turns into a post pull-and-reset is the norm, not the exception. That’s why we price the visit around what’s actually wrong, not what it says on the call sheet. Here’s what Bedford homeowners can expect:
- Hinge and latch repair: $140-$260
- Post pull-and-reset (cedar or steel): $280-$480 per post
- Iron gate weld and rust repair: $180-$520
- Sliding gate track and roller correction: $220-$640
- Operator control board or safety retrofit: $160-$400 (if replacement is required, we’ll quote a full number before you decide)
- Full gate replacement (like-for-like, common in Bedford): $1,200-$9,000 depending on material and size
Every estimate includes a written price delivered before any work starts. Always. Call (626) 649-4572 for a free estimate. And there’s no obligation to accept once you see the number.
We Also Serve Cities Near Bedford
Beyond Bedford, our gate repair crews cover Colleyville, Euless, Hurst, and North Richland Hills. Same written-price guarantee, same background-checked technicians, same care routine on every visit. If you’re in a neighboring Mid-Cities city, the drive to your gate is short.
Serving Bedford, TX - Our Local Coverage Area
We’re based in the Bedford area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Bedford
In Bedford, what looks like a hinge adjustment is usually a post problem. Your gate is probably fine. The post it hangs on is likely hollow at the soil line after decades in Tarrant County clay. We pull the post, reset it on a proper footing, and re-hang the panel. Most of the time, that’s cheaper than buying a new gate. Call (626) 649-4572 and we’ll tell you what you actually need. The estimate is free.
Sometimes, but not always. Older control boards from Viking, Ghost Controls, and DoorKing were built before modern safety and access standards. If the board won’t accept the signal, retrofitting usually means replacing the board or the whole operator. We’ll show you both costs in writing before you choose, so you can decide based on real numbers, not a sales pitch.
Because Bedford sits on Tarrant County’s expansive black clay. It shrinks during summer droughts when temperatures sit above 100°F, then swells after spring rains. That cycle lifts and drops your posts season after season. A properly dug footing with the right concrete bell and a post set below the active clay zone stops it. Our techs know how deep to go here, because they’ve seen this exact failure across Bedford’s mature neighborhoods for years.
Yes. UL 325 entrapment protection is a federal safety standard, and any automatic gate operator installed or retrofitted in Bedford should meet it. If your existing setup lacks working safety photocells or a reversing edge, we’ll flag it during the visit. The fix is often simpler than people expect. And if the old board won’t accept the safety hardware, we’ll quote it clearly.
If it’s a seized motor or a cracked weld, repair usually makes sense. If the control board is burned out and the operator is 25 years old, replacement is often the better long-term answer, especially when the board won’t support modern safety devices. We’ll give you a repair price and a replacement price side by side so you can compare honestly. Call (626) 649-4572 and we’ll walk you through it, no pressure.
Need a straight answer about your Bedford gate? Call Latch & Post Gate Repair at (626) 649-4572. A live person answers, day or night. You’ll get a written price before any work begins, and our 365-Day Done Right Promise means if it’s not right, we make it right.
Written by Cody Beckman, Owner at Latch & Post Gate Repair, serving Bedford and the surrounding Mid-Cities since 2009.