Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Taylor
Gate installation in Taylor runs $1,800 to $9,500 for most residential work, with the price set in writing before any material gets ordered. The number that matters more is the one tied to your soil: Taylor sits on Houston Black clay, the most expansive shrink-swell soil in North America, and a gate post set shallow will lean inside a few wet-dry seasons. We’re Latch & Post Gate Repair, and we’ve been part of the Cedarwell family since 2009. Our Gate Installation crews serve Taylor daily from the Austin office, and a live person answers when you call (626) 649-4572, nights and weekends included.
Why Latch & Post Gate Repair Is Taylor’s Preferred Gate Installation Company
Homeowners around Taylor keep our number because we say what things cost before we start. Every visit begins with a written price, not a vague estimate, and you approve that number before we touch a post or run a single wire. That matters on a new subdivision lot off Carlos G. Parker Boulevard, where a builder-installed operator may already be stalling, and it matters on an older acreage parcel off FM 973 where a steel pipe gate has leaned through two decades of wet-dry cycles.
Taylor families with kids and dogs care about how a crew leaves the property. Our technicians are background-checked and uniformed, and they follow the Cedarwell C.A.R.E. values on every job: Clean up like it’s our own home, Ask before we move or touch anything, Respect the family’s time and quiet hours, and Explain the price before the work. Shoe covers and drop cloths go down before anyone steps inside. Before we leave, you get a photo of the cleaned-up site.
Every gate comes down to two parts: the latch that holds it and the post that carries it. That’s the job we focus on, and every installation is covered by our 365-Day Done Right Promise. If it isn’t right, Latch & Post makes it right. No argument, no fine print.
Gate Opener Installation in Taylor
Gate opener installation in Taylor is the most common request we get from homeowners in new subdivisions east of Main Street, where builders hung ornamental iron swing gates and paired them with builder-grade LiftMaster or Linear operators that were never sized for the gate’s full travel weight. The job here usually involves more than bolting on a motor: we check the hinge post for plumb, verify the operator has a dedicated circuit, run low-voltage conduit for safety photocells and keypad entry, and set travel limits so the gate doesn’t stall mid-cycle. Typical cost in Taylor runs $1,400 to $3,800, depending on whether conduit already exists or we’re trenching fresh through clay.
Retrofitting a Manual Gate
Adding automation to a gate that was originally hung as a manual swing gate is a trench-and-pour project in Taylor, not an add-on. If no conduit or 120V circuit was stubbed at the gate during construction, we dig the run, lay schedule 40 conduit, pull the wire, and pour the operator pad before the motor ever gets mounted. Our crew does this work quietly, and we can schedule around nap time if that matters in your house.
Builder-Grade Operator Replacement
When a builder-grade operator has already failed or drifts its limits after each rain, we don’t band-aid it. We quote a replacement sized to your gate’s actual weight and cycle frequency, then re-tune the arms and safety photocells. Upfront pricing means you see the exact replacement cost in writing before we order parts.
Gate Fabrication in Taylor
Gate fabrication in Taylor falls into two distinct buckets: ornamental iron for the new subdivisions going up around the Samsung campus growth corridor, and heavy steel pipe for the older acreage lots that line the agricultural side of the city. We build to the gate’s actual duty: a double driveway swing gate on a ranch entrance off Chandler Road carries a very different load than a pedestrian gate next to a front door on a street behind Taylor High School. Fabrication and installation together typically run $2,200 to $9,500 in Taylor, with the written number in your hand before any steel is cut.
Custom Swing and Double Gates
For a double gate, we fabricate both leaves true and square, then hang them on posts we set ourselves. Every hinge post gets a bell-bottom pour in Taylor, because a straight-sided footing in Blackland clay will get jacked upward and tilted before the first full wet-dry cycle is done. We build the gate to carry the operator, not the other way around.
Pedestrian and Security Gates
Pedestrian gates in Taylor’s older in-town neighborhoods often replace chain-link panels that have rusted through at the hinges. We fabricate a steel frame with a proper latch and closer, and we match the existing post spacing so you don’t pay for unnecessary demolition. For security gates, we add a maglock or keypad entry and wire it through conduit, not zip-tied to the fence.
Trusted Brands We Service in Taylor
Our Taylor technicians are factory-trained on the equipment families actually own, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That means when a builder-grade Linear operator on a new Taylor subdivision gate drifts its limits, we adjust or replace it correctly on the first visit. We stock common Viking and DoorKing parts for Taylor customers, so a control board swap doesn’t sit waiting on a truck from Dallas. If your Ghost Controls opener is fighting a leaning post, we fix the post first, then tune the opener. Quick turnaround, and the parts are matched to your gate’s weight, not whatever is closest on the shelf.
Common Gate Installation Problems We See in Taylor Homes
- Hinge-post lean from Blackland clay. Taylor’s expansive soil contracts in summer drought and re-swells with fall rain, jacking shallow concrete collars upward and sideways. A gate that reads plumb in August is visibly leaning by April, and adjusting the hinges won’t hold because the post itself moved.
- Builder-grade operators stalling mid-travel. In post-Samsung subdivisions, we regularly find undersized LiftMaster or Linear units installed before the post footing was documented. The post moves a fraction of an inch, the operator’s limits drift, and the gate stops halfway through its cycle.
- Missing conduit and no dedicated circuit. Builders often leave the gate as a manual swing with no 120V stub or low-voltage run. Retrofitting automation means trenching through Taylor clay and pouring an operator pad, which is why we quote it as a full installation, not a weekend add-on.
- Frozen hardware after hard freezes. February 2021 cracked cast-iron hinges and knocked out operator boards across Taylor that weren’t rated for sustained sub-freezing temperatures. We replace cracked hardware with steel rated for the freeze-thaw cycles Taylor actually gets.
Pricing for Gate Installation in Taylor, TX
A pedestrian gate installation in Taylor runs $1,200 to $2,800. A single driveway swing gate with automation: $2,800 to $5,500. A double driveway gate, fabricated and automated, lands between $4,000 and $9,500. What moves the number is post footing depth, whether conduit already exists, and the gate’s weight and cycle frequency. You’ll see the exact figure in writing before any work begins, and that’s the price you pay. No invoice bigger than the quote, no add-on surprise. Call (626) 649-4572 for a free estimate at your Taylor property.
We Also Serve Cities Near Taylor
Our Taylor crews regularly run jobs in Hutto, Pflugerville, Round Rock, and Georgetown. The soil shifts as you move west toward the limestone edge, so we adjust post depth and footing design city by city. If you’re in one of those areas, the same written pricing and 365-Day Done Right Promise applies.
Serving Taylor, TX - Our Local Coverage Area
We’re based in the Taylor area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Installation in Taylor
The operator is usually fine. The hinge post has tilted out of plumb as Taylor’s Blackland clay re-swelled after the first fall rains, throwing the operator’s limits and the rack and pinion out of alignment. We break out the shallow builder footing, reset the post deeper with a bell-bottom pour, and re-tune the arms. Call (626) 649-4572 for an exact diagnosis, and the estimate is free.
Most manual swing gates can be automated if the gate itself is square and the hinges are solid. What most acreage properties lack is conduit, a dedicated 120V circuit, and a pad for the operator, which turns the job into a trench-and-pour project. We’ll tell you in writing whether your existing gate is worth automating or whether fabrication makes more sense. Call (626) 649-4572 and we’ll measure it for free.
Summer drought contracts Taylor’s Houston Black clay and pulls it away from the post, then fall and winter rains re-swell the soil and push the post back – often not to its original position. Each wet-dry cycle moves the concrete collar a little more, and by spring the lean is visible. A proper bell-bottom footing set below the shrink-swell zone stops the cycle. Call (626) 649-4572 for a post inspection and a written fix.
Yes. Any automatic gate operator in Taylor must have entrapment protection: safety photocells, a reversing mechanism, and, on many residential properties, a secondary edge sensor. We wire these through conduit and test them on every install, because a gate that meets code is a gate that won’t close on a kid or a dog. Call (626) 649-4572 and we’ll quote the full system, entrapment protection included, in writing.
It can be, but the answer depends on shade, gate weight, and how many cycles a day the gate runs. A light single swing gate with a clear southern exposure does fine on solar; a heavy double gate in tree shade will need a battery bank and possibly a larger panel. We’ll assess your specific gate and give you a straight answer in writing. Call (626) 649-4572 to schedule a free solar feasibility check.
Written by Cody Beckman, Owner at Latch & Post Gate Repair, serving Taylor since 2009.
Ready to talk about your Taylor gate? Call (626) 649-4572 for a free, written estimate. A live person answers day or night, and we’ll schedule a time that works for your family. Shoe covers on, drop cloths down, price agreed before we start, and a cleanup photo before we leave. That’s how we work in Taylor.