Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Installation Across Compton
Gate installation in Compton most often means rehabilitating a wrought-iron security gate from the late 1980s or 1990s that has finally given out after decades of marine-layer moisture and Santa Ana wind cycles. A new driveway gate in Compton typically runs from $1,850 to $4,200 for a standard single swing gate, while a matched driveway and pedestrian gate package usually lands between $3,400 and $7,800 depending on the ironwork, the operator, and what has to happen to the existing concrete. We know these blocks because we work them every week. Call (626) 649-4572 and we’ll send a technician who will look at your specific gate, give you a written price before anything starts, and leave your driveway cleaner than he found it.
We’re Gate Installation specialists at Latch & Post Gate Repair, part of the Cedarwell family of independently owned gate specialists. This page is about one thing: what Compton homeowners should actually expect when they need a gate installed, replaced, or retrofitted on a 1950s bungalow lot with settled concrete. If you live off Compton Boulevard, Wilmington Avenue, or in the blocks around Gonzales Park, we’re the crew that shows up in a uniform, introduces himself at the door, and writes the number down before he touches a hinge.
Why Latch & Post Gate Repair Is Compton’s Preferred Gate Installation Company
Since 2009, Latch & Post has focused on exactly one trade: gates. Not fences, not general contracting. Every gate comes down to two parts, the latch that holds it and the post that carries it, and that narrow focus is why Compton homeowners call us for work that other companies misdiagnose. We’re not a handyman service that does gates on the side. We’re a gate company.
The kinds of gates common in Compton are older than what you’ll find in Gardena or Carson, and that matters. A 1993 wrought-iron swing gate on a narrow lot off Rosecrans Avenue needs a different diagnosis than a 2018 aluminum gate in a newer subdivision. Our technicians are trained on the brands families in Compton actually own: Viking, Ghost Controls, DoorKing, and Elite among them. When a burned-out operator shows up on an overweight layered gate, we know to check the gate leaf weight before we quote a motor swap, because swapping the motor without fixing the weight means you’ll be calling again in eighteen months.
Every Compton job is covered by the 365-Day Done Right Promise. If the installation isn’t right, Latch & Post makes it right. No argument, no fine print. And every call is answered by a live person, 24 hours a day, seven days a week, including the Tuesday night when your gate drops off its bottom hinge. No voicemail tree. No callback queue.
We also bring the Cedarwell C.A.R.E. routine to every Compton home: a written price before any work begins, shoe covers and drop cloths inside the house, a photo of the clean-up before we leave, and quiet tools when kids are asleep. Cody Beckman set that standard, and our Compton customers hold us to it.
Gate Installation Services in Compton
Gate Installation Services in Compton center on a specific reality: most of the wrought-iron security gates on these blocks went in during the late 1980s and 1990s, and many have been altered over the years with welded-on bars and added locks. A new gate install here is rarely a blank canvas. It’s more often a replacement of an exhausted gate on a settled slab, or a retrofit of a gate frame that’s still structurally sound enough to keep. We’ll tell you honestly which one you’ve got, because sometimes the cheaper answer is a new post footing and hinges, and sometimes the cheaper answer is a new gate.
Driveway Swing Gates
A single driveway swing gate in Compton runs $1,850 to $4,200, installed, with the operator included in the middle of that range. The price depends on whether we’re reusing your existing concrete or pouring a new post footing. Most Compton driveway slabs from the 1940s to 1960s have settled, so we often saw-cut and pour fresh footings rather than bolt into cracked, shifting concrete.
Pedestrian and Security Gates
A matching pedestrian gate beside a driveway gate runs $900 to $2,400 on its own. That’s the gate most Compton homeowners actually use daily, and it’s the one where a sagging hinge post from an old 1950s concrete pour shows up first. We reset the post, rehang the gate, and it swings like it did when it was first welded.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Electric Gate Installation in Compton
Electric Gate Installation in Compton usually means putting a new operator on an old gate, and that’s where we see the most preventable failures. A new swing gate operator installed in Compton runs $1,100 to $2,800, including the safety photocells and the control board. A slide gate operator runs $1,400 to $3,200 depending on the gate’s weight and the length of track we need to set. If the existing gate has been layered with welded bars over the years, the operator has to be sized for the actual weight of the leaf, not the original spec from 1994.
Operator Replacement on Existing Gates
When the motor burns out or the gears strip on an older Viking or DoorKing operator, we don’t just unbolt the old box and hang a new one. We weigh the gate leaf, check the hinge post, and confirm the control board is compatible with modern UL 325 entrapment protection. Then we quote the whole job in writing, before any work starts.
Safety Retrofit for Older Installations
Most Compton gates built before 2000 have no working photocells, no edge sensors, and a control board that predates current safety standards. A safety retrofit, with new photocells, a compliant control board, and recalibrated force settings, runs $500 to $1,100 on top of the operator. We won’t install a new operator without bringing the safety side up to code, because a gate that can’t reverse on obstruction is a liability, not a convenience.
Trusted Brands We Service in Compton
Our Compton technicians are factory-trained on the operators families here actually have: Viking, Ghost Controls, DoorKing, Elite, LiftMaster, FAAC, BFT, Linear, and Mighty Mule. When a control board fails on a 1996 DoorKing slide operator, we stock the replacement board locally and can usually have the gate running the same week, not the same month. We don’t push one brand. We service what’s on your post and tell you straight if a different operator makes more sense for the weight of your gate.
Common Gate Installation Problems We See in Compton Homes
- Layered gates overpowering their operators. On a narrow lot off South Wilmington Avenue, our tech found a 1994 wrought-iron swing gate that a tenant had doubled with welded bars, and the LiftMaster operator was tripping at startup. We pulled the gate, reset the hinge post in a new concrete post footing, removed the added bars, and reinstalled the original operator. No new gate needed. A month later the same client had us add keypad entry and a fresh safety photocell so the UL 325 entrapment protection would actually work.
- Hinge post rot in settled 1950s concrete. Compton bungalows were built on original concrete driveways that have cracked and settled for seventy years. The hinge post sits in that old pour, and when it shifts, the swing gate drops every cycle. You can straighten the gate panel, but it’ll sag again in a season if the post footing isn’t addressed first.
- Marine-layer corrosion at the welds and hinge points. Compton sits ten to twelve miles inland, close enough to the coast that daily marine moisture settles on bare iron at every weld. Then Santa Ana winds crack the paint and expose the metal to the next moisture cycle. Properties cycle through rust-repair-repaint every few years until the hinge post itself rusts through, and that’s when we’re called for a replacement rather than a patch.
- Obsolete control boards on operators that predate current safety rules. The original 1990s control board was never rated for a gate that doubled in weight from welded-on security bars. The board fails first, then the motor overheats, and the homeowner is left with a gate stuck half-open on a Saturday. We replace the board, verify the force settings, and add photocells if the original install skipped them.
Pricing for Gate Installation in Compton, CA
Here is the honest pricing for Compton market work. A pedestrian gate runs $900 to $2,400. A single driveway swing gate runs $1,850 to $4,200 installed with operator. A matched driveway and pedestrian package runs $3,400 to $7,800. A slide gate installation runs $2,600 to $5,800 depending on track length and site prep. A control board replacement runs $350 to $900. A hinge post reset with new concrete footing runs $600 to $1,400. Every one of those numbers is quoted in writing before we start, and the price you see is the price you pay. Call (626) 649-4572 for a free estimate on your specific gate.
We Also Serve Cities Near Compton
We serve Compton neighborhoods daily, and we also run crews to Gardena, Carson, Lynwood, and Paramount. If you’re a homeowner in one of those cities with a gate that’s sagging, stalling, or simply old enough to vote, call the same number and we’ll schedule a visit. The written pricing, the shoe covers, and the 365-Day Done Right Promise apply everywhere we go.
Serving Compton, CA - Our Local Coverage Area
We’re based in the Compton area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Installation in Compton
Yes, in most cases we can replace just the operator without replacing the gate. In Compton, the catch is that many older iron gates were layered with welded security bars over the years, and that added weight may have killed the motor in the first place. We weigh the gate leaf before quoting an operator swap, and if the gate is too heavy for a standard operator, we’ll tell you that in writing. A straight operator replacement runs $1,100 to $2,800. Call (626) 649-4572 and we’ll give you the exact number for your gate.
Not necessarily. Often the gate panel itself is fine and the problem is the hinge post, which was set in old 1950s concrete that has settled and cracked. We reset the post in a new concrete footing, rehang the gate, and it usually swings correctly again. A post reset runs $600 to $1,400. If the post has rusted through entirely, then replacement is the honest answer, and we’ll show you the rust before we quote anything.
It is a problem, and it is one we fix on nearly every Compton install. Pre-2000 gates often have no photocells, no edge sensors, and control boards that don’t meet current UL 325 entrapment standards. When we install a new operator, we bring the safety side up to code: new photocells, compliant control board, recalibrated force settings. The safety retrofit runs $500 to $1,100 on top of the operator, and we include it in the written quote before any work starts.
Yes, and narrow lots with cracked slabs are the standard conditions for Compton work, not the exception. A slide gate needs a longer track run, so on a narrow lot it often makes more sense to install a swing gate instead. A swing gate can be hung from a new post footing poured beyond the cracked section of the old slab. We’ll look at your specific driveway layout and give you a straight recommendation with real numbers. Call (626) 649-4572 for a free on-site estimate.
In Compton, the most common cause of stripped gears and stalling motors is an overweight gate, not a defective operator. Gates from the 1990s that were later layered with welded security bars often weigh two to three times what the original operator was rated for. The motor has been fighting that weight for years, and the gears finally gave out. We’ll weigh the gate, tell you whether the gate needs lightening or the operator needs up-sizing, and give you a written quote for whichever fix is actually correct.
If your gate is sagging, stalling, or simply old enough that you’re not sure it’ll close tonight, call us. Cody Beckman and the Latch & Post crew serve Compton every week, and we’ll give you a straight answer, a written price, and clean floors when we leave. Call (626) 649-4572 for a free estimate.
Written by Cody Beckman, Owner at Latch & Post Gate Repair, serving Compton since 2009.