Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Redmond, WA
Latch & Post Gate Repair handles gate repair, gate installation, and electric gate repair across Redmond, from the planned-community subdivisions of Redmond Ridge and Bear Creek to the older homes on Education Hill. Redmond’s combination of Microsoft-era automated gate systems now aging out, persistent fall-through-spring rain, and clay-heavy soils near the creek means many calls here are more involved than a simple hinge adjustment. Call (626) 649-4572 and you’ll reach a live person who can talk through what’s happening with your gate before you spend a dollar.
Why Redmond Homes Are Different
Redmond’s residential base tilts heavily toward planned subdivisions built between the mid-1990s and the 2010s, where HOA covenants often specified cedar or vinyl privacy fencing with a matching automated driveway gate. Those gates are now 15 to 25 years old. The operators that ran them, often app-controlled LiftMaster units installed during the original build, are reaching the point where control boards corrode, sensors drift, and integration with newer home automation platforms starts failing. In Redmond, a squeaking gate is rarely just a lubrication issue. It’s the first sign of a component that’s been sitting in maritime moisture for two decades.
Climate does specific damage here. Redmond’s inland position near the Cascade foothills brings freeze-thaw cycles slightly more pronounced than Seattle’s, which rusts hinges and latches faster and swells wood frames out of square through the wet months. Clay-heavy soil in low-lying areas near Bear Creek heaves seasonally, which can push gate posts out of alignment on a gate with no mechanical fault at all. We see this on Education Hill too, where 1970s wood-post construction has absorbed decades of ground-level moisture. Redmond gate work is as much about understanding what the ground and weather are doing under the gate as it is about the hardware on top of it.
There’s also a permitting reality that only applies to certain Redmond properties. Homes backing up to Bear Creek or mapped wetland buffers fall under King County critical areas regulations, which restrict ground disturbance within setback zones. If a post replacement requires digging in one of those zones, a county review has to happen before we can legally put a shovel down. We build that timeline into the written estimate from the start rather than discovering it mid-job the way an out-of-area contractor might.
Our Main Redmond Services
Most Redmond calls break down into three areas. Each one has its own page with detailed pricing, timelines, and what to expect from the first visit.
Gate Repair in Redmond
A gate that drags, sticks, or won’t latch in Redmond usually traces back to moisture. Swollen wood from the wet season, rusted hinges from repeated freeze-thaw, or posts that have shifted in Bear Creek clay all put the frame out of square. We fix what’s actually failing, not just the symptom, and we carry parts for the brands Redmond homes actually have. Every repair starts with a written price before we touch anything, plus shoe covers and drop cloths inside the home. Gate Repair in Redmond covers the full scope, from latch replacement to post resetting.
Gate Installation in Redmond
New gate installations in Redmond’s planned communities almost always involve HOA specifications we need to match, often cedar or vinyl privacy gates in a style the covenants already defined. We’ll confirm the HOA requirements before ordering materials, then handle the full install including post setting, frame hanging, and hardware. Where the property falls within a critical areas zone, we’ll walk through the county review step before any digging starts. Gate Installation in Redmond explains the process from measure to cleanup photo.
Electric Gate Repair in Redmond
Redmond’s concentration of 2000s-era automated gate systems means we diagnose a lot of moisture-damaged control boards, failed safety sensors, and operators that have lost sync with their app. These systems need more than a mechanical fix; they need someone who understands the electronics and can re-integrate the gate with the home’s current automation setup without telling you to rip everything out. Electric Gate Repair in Redmond covers operator diagnostics, board replacement, and safety edge testing.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Redmond
We’re factory-trained on the brands Redmond families actually opened their driveways with, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. See our brands for the full list. Common parts for these operators are stocked on our service vehicles, so a control board or sensor replacement usually happens on the first visit rather than a week later.
Pricing for Gate Company in Redmond, WA
These are the ranges we typically quote in Redmond. You’ll see your exact number in writing before any work begins, and you’ll have the chance to decline on the spot with no charge.
| Service | Typical range in Redmond |
|---|---|
| Standard gate-latch replacement | $145-$285 |
| Hinge replacement (two hinges) | $180-$320 |
| Gate frame re-square and re-hang | $350-$650 |
| Gate post reset (above-ground, no dig) | $280-$520 |
| Gate post replacement (set in concrete) | $620-$1,100 |
| Gate operator control board replacement | $320-$590 |
| Safety sensor replacement (pair) | $190-$340 |
| Operator remotes programmed (two remotes) | $95-$160 |
| Motor replacement (full operator swap) | $850-$1,700 |
| Full automated gate package (operator, safety edges, keypad) | $2,800-$5,200 |
What pushes a Redmond quote toward the upper end is usually soil. Posts in clay-heavy ground near Bear Creek that have heaved seasonally may need deeper concrete footings or, where wetland buffers are involved, a county review before digging. You’ll see that in the written price up front. We don’t deliver an estimate and then add line items later.
Neighborhoods We Serve in Redmond
We work throughout Redmond and typically reach most homes within a day of the first call. These are a few of the neighborhoods we see regularly:
- Redmond Ridge
- Education Hill
- Bear Creek
- Downtown Redmond
- Grass Lawn
Service Area – Cities Near Redmond
Latch & Post Gate Repair serves Redmond as our local focus, with dispatch and scheduling coordinated from the brand’s Seattle office. If you’re a few minutes outside Redmond, we also work in Kirkland, WA, Sammamish, WA, Bellevue, WA, and Woodinville, WA.
Serving Redmond, WA - Our Local Coverage Area
We’re based in the Redmond area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Redmond
Most non-emergency repairs are scheduled within one to two days of your call. Our phones are answered by a live person around the clock, so if a gate has failed closed and is blocking the driveway, we’ll prioritize the call and get a technician to you as quickly as the schedule allows. Call (626) 649-4572 and you’ll get a straight answer on timing before anything is booked.
Yes. For installations and post replacements, we confirm any HOA specifications before materials are ordered and we’ll identify whether the property falls under King County critical areas regulations. Where a county review is required, we include that timeline in the written estimate so there are no surprises after the work starts.
Every repair and installation is covered by the 365-Day Done Right Promise. If something isn’t right within a year of the work, Latch & Post makes it right, no argument and no fine print. That’s the same promise we’ve operated under since 2009 as part of the Cedarwell family.
If your gate is dragging, stuck, or stopped responding to the remote, call (626) 649-4572. You’ll reach a live person, get an honest read on what’s happening, and receive a written price before any work begins. Estimates are free, and there’s no obligation to proceed.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Redmond Customers Say
"The gate screeched and dragged. They fixed the track and oiled it, and wiped down everything after so there was no mess. Quiet and kind, in and out without any fuss."
- Opal Reddick"Our gate opener quit and they came out quick. The tech was careful not to leave the yard open while our dog was out, which I really appreciated. Clean work, swept up the metal shavings."
- Eleanor Boggs"New hinges welded on a heavy gate. They laid down protection so no sparks hit the driveway and cleaned every bit after. Respectful of the property and the result is solid."
- Derek Pulanco