Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Electric Gate Repair Across San Bruno
Electric gate repair in San Bruno usually costs between $185 and $540 for most opener, sensor, and control board fixes, and we can typically get a technician to your home the same day you call. The work we do here is shaped by one thing more than anything else: the San Bruno Gap. That wind corridor off the Pacific pushes gates harder than almost anywhere else on the Peninsula, which means openers cycle and fail in ways you simply don’t see in Millbrae or Burlingame. If your gate is reversing on its own, binding on the track, or won’t respond to the remote, call (626) 649-4572 and we’ll give you a written price before any work begins.
Why Latch & Post Gate Repair Is San Bruno’s Preferred Electric Gate Repair Company
We’re part of the Cedarwell family of independently owned gate specialists, and we’ve been at this since 2009. Every gate comes down to two parts – the latch that holds it and the post that carries it. That’s the job we focus on. San Bruno homeowners call us because our technicians understand the local failure patterns: a gate that worked fine in 2005 is now fighting wind gusts that trip the obstruction sensor four times a week, and the hinges are corroding from salt air coming off both the ocean and the bay. We don’t guess at that. We quote for it.
Cody Beckman leads our crew, and every technician who rolls up to a San Bruno driveway is background-checked, uniformed, and trained on the brands families actually own: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. We lay drop cloths on the floor and put on shoe covers before we step inside your home, and we choose pet-safe lubricants where there’s a choice. When the job is done, you get a photo of the cleanup before we leave. That’s the Cedarwell C.A.R.E. routine – not an upsell, just how we work.
Commercial Gate Operator in San Bruno
Commercial Gate Operator work in San Bruno means repairing or replacing the motor and drive assembly on sliding or swing gates at small commercial properties, HOAs, and the occasional multi-unit building. A typical commercial operator repair in San Bruno runs $340 to $1,100 depending on whether the failure is the motor, the limit switch, or the control board itself. Cody Beckman and the team start by checking the actual condition of the post and track – on the windy side of town, a commercial slide gate can be perfectly level one season and binding the next because the post has leaned just enough to fight the roller wheels.
Motor and Limit Switch Diagnosis
On commercial slide gates especially, San Bruno wind loads mean the limit switch settings drift out of alignment faster than they would in South San Francisco or Brisbane. We recalibrate open and close limits against the real-world travel of the gate, not the factory defaults. If the motor is drawing too many amps on startup, that’s usually a load problem – and on older installations near the Crestmoor area or west of Skyline, that load problem often traces back to a post that shifted years ago.
Control Board Replacement and Retrofits
Older commercial operators built before modern obstruction-reversal standards can sometimes be retrofitted with a current control board, but not always. When the board is obsolete and no drop-in replacement exists, we’ll tell you honestly: a new operator head is often the cheaper answer than chasing parts. You’ll see the written price for either path before we order anything.
Gate Opener Repair in San Bruno
Gate Opener Repair in San Bruno covers swing and slide gate openers on single-family homes across the flat grid east of El Camino Real, the hillside streets west of Skyline, and everything in between. Most opener repairs here run $185 to $480. The most common failure we find isn’t the motor itself – it’s the control board or limit settings being thrown off by the constant wind cycling through the Gap. An opener that reverses mid-travel is usually tripping its obstruction sensor because wind pressure is flexing the gate panel.
Swing Arm and Drive Rail Alignment
On a flat block east of El Camino Real, our tech answered a call about a LiftMaster swing gate operator that kept reversing halfway open. The gate was an original 1950s wrought-iron panel on a wood hinge post set in a heaving 1950s concrete pad. Instead of just swapping the opener, we reset the post footing and did a full sag correction. After re-rigging the operator, realigning the arm, and testing the safety photocell, the gate cycled cleanly with no false trips. The homeowner was quoted the post-reset upfront – that’s the kind of hidden concrete-pad failure we warn San Bruno customers about before we start.
Remote and Keypad Troubleshooting
When a remote stops working or a keypad won’t accept the code, we check the receiver and the antenna routing first. In San Bruno’s older housing stock, the original operator antenna is often buried inside a metal post or corroded at the connector from years of salt air. We’ll test the signal path, replace the receiver if needed, and reprogram remotes and keypads before we leave – quiet tools and all, so we won’t wake a sleeping kid in the front bedroom.
Trusted Brands We Service in San Bruno
We’re factory-trained on Linear, Viking, Ghost Controls, and DoorKing – four brands that show up constantly on San Bruno’s mix of mid-century and newer properties. Because we work on these systems every week, we keep common control boards, safety sensors, remotes, and limit switches stocked in our San Francisco Bay Area service vehicles, so a San Bruno repair doesn’t stall out waiting for a part to ship. If your opener is a LiftMaster or FAAC, we service those too, along with BFT, Elite, and Mighty Mule. The right fix happens on the first visit because we’re not guessing at the brand – we know it.
Common Electric Gate Repair Problems We See in San Bruno Homes
- Endless cycling from Gap wind gusts. When Pacific wind funnels through the San Bruno Gap, it racks older swing and slide gate frames and trips the obstruction sensor repeatedly. The opener opens, senses resistance, reverses, and starts again – until we recalibrate limits and sensitivity for actual wind load.
- Corroded hinges and post bases from dual salt air. Marine layer rolls in from the west and bay humidity pushes in from the east. Steel post bases and hinge hardware here can show serious rust failure in 8 to 10 years, compared to 15 in sheltered Burlingame.
- Heaving or tilted 1950s concrete and wood posts. San Bruno’s post-WWII homes were built with gate posts never engineered for motorized openers. Decades of wind loading can heave a post enough that a simple hinge swap becomes a full post footing reset.
- Obsolete control boards on legacy openers. Older automatic operators turned off safety standards years ago. Many San Bruno gates pre-date modern obstruction-reversal requirements. When the board fails and no drop-in replacement exists, a new operator head is often cheaper than continued patching.
Pricing for Electric Gate Repair in San Bruno, CA
Here’s what San Bruno homeowners can expect to pay. A standard gate opener repair runs $185 to $480. Commercial gate operator repairs run $340 to $1,100. A control board replacement typically lands between $240 and $540. A keypad or remote receiver fix is usually $120 to $285. Full post resets and footing corrections – the kind of thing older San Bruno properties need when the original concrete pad has failed – run $600 to $1,600 depending on the post material and depth. Every price is quoted in writing before we touch anything. Call (626) 649-4572 for a free estimate, and you’ll see the exact number before any work starts.
We Also Serve Cities Near San Bruno
Our technicians regularly work in Millbrae, South San Francisco, Pacifica, and Brisbane. If your gate sits on the windward side of a hill or down a flat street near the bayshore, we’ve likely already fixed the same failure pattern nearby. You can read more about our Electric Gate Repair services, or see how we cover San Bruno specifically. Same crew, same written-price promise, same C.A.R.E. routine at every visit.
Serving San Bruno, CA - Our Local Coverage Area
We’re based in the San Bruno area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in San Bruno
Your gate is tripping its obstruction sensor because wind gusts funneling through the San Bruno Gap flex the gate panel enough to trigger a false obstruction reading. Millbrae and South San Francisco don’t get the same sustained wind load, so they don’t see this failure mode as often. The fix is recalibrating the opener’s limit and sensitivity settings for the real-world wind load on your specific gate. Call (626) 649-4572 and we’ll diagnose it at your home.
In most cases, we can retrofit a modern operator onto an existing mid-century gate if the post itself is still sound. The real question is the post. If the original concrete pad has heaved or the wood has rotted from decades of salt air, a full post reset is needed before any operator will work reliably. We’ll quote both paths honestly, and you’ll see the written numbers before you decide.
Yes. Modern automatic gates in San Bruno are required to have functioning safety sensors – photocells on swing gates and contact edges on slide gates – that stop and reverse the gate if a person, pet, or car is in the path. We test and realign sensors on every repair. If your gate is missing them or they’re non-functional, we’ll quote the retrofit in writing as part of the estimate.
San Bruno gets hit from two directions: marine layer off the Pacific to the west and bay humidity to the east. That dual salt-air exposure accelerates corrosion on steel hinges, latch hardware, and post bases. Hardware that lasts 15 years in Burlingame can fail in 8 to 10 years in San Bruno. We use corrosion-resistant replacement parts and can discuss coatings and treatments that hold up better here.
We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Our technicians are factory-trained on these brands, and we keep common parts stocked in our Bay Area service vehicles. If we don’t have the part in the truck, we can usually have it the next business day. Call (626) 649-4572 and tell us the brand – we’ll tell you what to expect before we arrive.
Written by Cody Beckman, Owner at Latch & Post Gate Repair, serving San Bruno since 2009 as part of the Cedarwell family of gate specialists.