Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterGate Company in Rialto, CA
Gate work in Rialto follows a split personality that most gate companies never prepare for. You have 1960s and 1970s block-wall homes with 40-year-old ornamental iron swing gates on the residential side, and on the commercial side, miles of Class IV slide gates moving semi-truck traffic through the warehouse corridor along Ayala Drive and Linden Avenue. Add in Santa Ana winds that funnel straight down Cajon Pass at 60-plus mph, and you get a repair market where wind damage, hinge fatigue, and thermal expansion show up together. If you need a gate company in Rialto that works both sides of that divide, call Latch & Post at (626) 649-4572.
Why Rialto Homes Are Different
Most of central and south Rialto was built between 1960 and 1985. The original gates on those lots were tubular steel or wrought iron swing gates hung on concrete block wall pilasters. We regularly see hinge pins that have rusted through, gate frames that sag three or four inches at the latch side, and block wall anchors that crumbled around the hinge bolts.
The summers here routinely push past 105°F, and that heat accelerates oxidation on bare iron and untreated steel. But the bigger seasonal problem is wind. The Cajon Pass funnels Santa Ana events straight into Rialto, and a gate that has quietly rusted for years will twist or separate from its post in one bad afternoon. North Rialto, especially the newer subdivisions near the 210 corridor, has a different profile: HOA-governed automated driveway gates with modern operators that fail differently, usually on limit switches or photo eyes rather than structural steel.
There is also the hard water. Rialto groundwater leaves mineral scale on hinge pins and inside operator housings. We see seized hinges and corroded control board contacts here more often than in Fontana or Bloomington. A gate that will not budge is rarely just a hinge issue in Rialto; it is usually mineral buildup that has been building for years.
Our Main Rialto Services
Most Rialto calls fall into one of three buckets: a sagging or wind-damaged swing gate, a full replacement on an aging block-wall opening, or an electric operator that has stopped responding. Each service has its own Rialto page with local pricing and the details of how we work.
Gate Repair in Rialto
A typical repair here means re-hanging a sagging gate, replacing hinge hardware, or rebuilding the post anchor where the block wall has failed. Older ornamental iron gates almost always need hinge work before anything else, and we often find the latch side has dropped far enough that the gate no longer closes without lifting. On commercial slide gates near the airport redevelopment, repairs lean toward roller trucks and track alignment. See the full breakdown on our Gate Repair in Rialto page.
Gate Installation in Rialto
New gate work in Rialto usually means working within an existing block wall opening, which limits what can be installed without masonry changes. We measure the opening, check the pilasters for sound concrete, and quote the full job with a written price before anything is ordered. For north Rialto HOAs, we are used to matching community standards and submitting the paperwork before a post hole gets dug. Details are on the Gate Installation in Rialto page.
Electric Gate Repair in Rialto
Electric gate failures in Rialto split between operator wear from heat and wiring problems made worse by hard water and dust. We work on FAAC, BFT, Linear, and Viking operators most weeks, and we stock common boards and limit switches locally so a diagnostic visit often ends with the gate working that day. If you have a gate that opens but will not close, or an operator that hums and does not move, see the Electric Gate Repair in Rialto page for the full story.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Brands We Service in Rialto
We are factory-trained on the brands Rialto homeowners and property managers actually run: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Our technicians stock common FAAC and Linear parts on the truck, so many electric gate repairs finish in one visit. Learn more on our brands page.
Pricing for Gate Company in Rialto, CA
Every price below is the range you should expect before we arrive. You will get a written quote before any work starts, and that number does not move unless we find something hidden and you approve the change first. Rialto’s older iron gates often need more labor than a newer neighborhood’s gates because the hardware has to be cut or drilled off rather than unbolted.
| Service | Typical Range in Rialto |
|---|---|
| Standard gate latch replacement | $95 - $185 |
| Gate hinge repair (one hinge) | $120 - $240 |
| Re-hang sagging gate (adjust and align) | $180 - $340 |
| Post anchor rebuild on block wall | $250 - $475 |
| Gate frame straightening (wind damage) | $220 - $420 |
| Full gate replacement (standard residential swing) | $900 - $2,800 |
| Electric operator diagnostic | $85 - $165 |
| Operator board replacement | $240 - $520 |
| Limit switch replacement | $160 - $310 |
| Photo eye alignment or replacement | $120 - $280 |
What pushes a price up in Rialto? Two things mostly. First, access: if the post side of the gate is tight against a neighbor’s wall or a masonry column, we have to work from one side, which takes longer. Second, the age of the hardware: 40-year-old hinges are usually rust-welded and need to be cut out rather than unbolted. Neither changes our promise: the written price comes before the work, always.
Neighborhoods We Serve in Rialto
We work across all of Rialto, from the older grid streets south of the 10 to the newer HOA communities up toward the 210. We know the block-wall backyards of the central neighborhoods and the gate-operator-heavy north end equally well.
- Central Rialto (older block-wall homes, 1960s-70s iron gates)
- North Rialto near the 210 (newer HOAs, automated driveway gates)
- West Rialto along Riverside Avenue
- Las Colinas and the neighborhoods east of Cedar Avenue
- Rialto Airport Business Park and surrounding commercial corridor
Because our scheduling runs out of the Inland Empire office, most Rialto calls get a same-day or next-day visit depending on the season. During Santa Ana events, wind-damage calls spike and we prioritize gates that are stuck open or blocking access.
Service Area – Cities Near Rialto
We also serve homeowners in Bloomington, CA, San Bernardino, CA, Fontana, CA, and Grand Terrace, CA. If you are on the Rialto edge and not sure whether you are in our area, call and ask. A live person answers, day or night, and will tell you straight.
Serving Rialto, CA - Our Local Coverage Area
We’re based in the Rialto area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Rialto
Most Rialto repair calls are scheduled same-day or next-day. During Santa Ana wind events, we prioritize gates that are stuck open or blocking a driveway, since those are safety and security issues. Call (626) 649-4572 and you will get a live person, not voicemail, any time of day.
In the HOA-managed communities north of the 210, yes, most gate replacements need design or architectural committee approval. We can handle the paperwork and often have the spec sheet ready before your committee meeting. In the older central neighborhoods there is typically no review beyond standard building code.
Yes. Our technicians regularly service the Class IV and V slide gates and barrier arms serving distribution centers along Ayala Drive and Linden Avenue. If you manage a commercial property in Rialto’s warehouse district, call us and we will put together a maintenance schedule rather than running repair-to-repair.
We serve all of Rialto plus Bloomington, San Bernardino, Fontana, and Grand Terrace. If you are not sure whether your street is in our service area, call and ask. That call is answered by a person, not a recording.
If your gate is sagging, stuck, or dead at the operator, call (626) 649-4572 for a free estimate. We will give you a written price before any work starts, and we leave your gate working and your property clean when we go.
What happens when you call
- 1A real person answersNo phone trees - talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you - the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Rialto Customers Say
"Electric gate was acting up. He was calm and methodical, found the bad sensor, and tidied the whole area by the gate post when he finished. No grease left on the driveway."
- Ravi Menon"Gate motor died and they replaced it carefully, cleaning every bit of debris off the driveway. Mindful not to leave the yard open with our dog out. Great crew."
- Benson Ide"The gate screeched and dragged. They fixed the track and oiled it, and wiped down everything after so there was no mess. Quiet and kind, in and out without any fuss."
- Opal Reddick